Car body elements Audi 100 C3

Removal and installation the front buffer
Upper buffer mount 1 - screw; 2 - buffer Execution order 1. Remove the decorative trim (1) by carefully prying it up with a screwdriver. 2. Unscrew the five...

Removal and installation the radiator grille
Execution order 1. Open the hood and unscrew the central mounting screw of the radiator grille (1 – screw; 2 – clamp). 2. Remove the trim from both side...

Removal and installation the hood
Execution order 1. Open the hood. 2. Mark the location of the hinge brackets relative to the hood by tracing them, for example, with a felt-tip pen. 3. For gas...

Adjusting the bonnet lock cable
Adjusting the bonnet lock cable 1 - locking lever; 2 - clamp; 3 - cable; 4 - bolt Execution order 1. Loosen the clamp mounting bolt. 2. Pull the cable out to...

Replacing the locker
Mounting the lokar 1 - screw; 2 - washer; 3 - plastic nut Execution order 1. Loosen the wheel mounting bolts. 2. Raise and support the front of the vehicle. 3....

Front wing
Lower rear front fender mount 1, 2 - screw; 3 - washer Front fender upper mount 1 - bolt; 2 - front wing Removal 1. Remove the front bumper (see subsection...

Replacing the molding
Execution order 1. Remove the plug (1) from the end of the molding (2) by carefully prying it up with a screwdriver 2. Remove the molding from the plastic...

Replacing the door glass seal
Execution order 1. Lift the glass seal (1) with a plastic or wooden spatula (2) and remove it. 2. Install the seal in the reverse order. When installing, make...

Door trim (vehicles produced before December 1987)
Front door 1 - lock button; 2 - socket of the inner door lock handle; 3 - handrail; 4 - window lift handle; 5 - interior upholstery Removal 1. Remove the inner...

Replacing door glass and window lifter
Fastening the inner door panel 1 - door frame; 2 - inner panel; 3 - lock handle cable; 4 - bolt Window regulator parts 1 - glass; 2 - window lifter; A - glass...

Removal and installation the door
Execution order 1. Remove the door trim. 2. Disconnect the connectors with wires from the connectors on the door and remove the wiring from the door. 3. Drill...

External door handle
External door lock handle 1,2 - rotary brackets; 3 - handle; 4 - screw; 5 - retaining ring; 6 - drive lever; 7 - spring; 8 - casing; 9 - sealing ring; 10 -...

Door lock
Removal the door lock 1 - traction; 2 - bushing; 3 - lock Locking the drive lever of the lock 1 - drive lever; 2 - mounting hole; 3 - lock lever Door locking...

Adjusting the door lock
Execution order 1. Open the door. 2. To check the adjustment, mark the initial position of the latch washer by tracing it with a felt-tip pen. 3. Loosen the...

Removal and installation an electric window lift
Electric window lift parts 1 - relay and fuse box; 2 - additional block; 3 - thermal fuse (20 A); 4 - connector; 5 - switch on the passenger side door; 6 -...

Removal and installation the outside rearview mirror
Execution order 1. From inside the cabin, remove the decorative plug, unscrew the mounting screw and remove the mirror adjustment handle. 2. Remove the plug...

Replacing the reflective element of the outside rearview mirror
Replacing the reflective element of a mirror with a mechanical drive 1 - body; 2 - adjusting slider; 3 - reflective element; 4 - spring; 5 - latch Execution...

Repair of the rear window heating element
Execution order 1. First, turn on the current heating and check if there is voltage at the contacts of the current heating element using a tester or a test...

Removal and installation the rear buffer
Execution order 1. Remove the covering from the bottom of the luggage compartment. 2. From the luggage compartment, unscrew two mounting bolts on both sides...

Removal and installation the trunk lid
Execution order 1. Disconnect the wire from the negative terminal of the battery. 2. Disconnect the connectors with wires from the rear lights. 3. Mark the...

Removal and installation the trunk lid lock
Execution order 1. Open the trunk lid. 2. Unscrew the fastening nuts and remove the lock with gaskets from the studs. 3. Disconnect the rod from the lock lever...

Replacing the rear decorative trim with a niche for the license plate
Execution order 1. Remove the license plate. 2. Remove the decorative trim (2) by prying it off with a screwdriver (3) in the area of the mounting bracket (at...

Removal and installation the center console
Removal the center console cover (models produced before December 1987.) 1 - screw; 2 - lid; 3 - center console Removal the center console frame (models...

Cleaning the gutters (on models equipped with a hatch)
Location of water drains 1 - front water drainage; 2 - rear water drainage It is recommended to clean the gutters using an old speedometer drive cable and an...

Removal and installation the heater
Heating and ventilation system 1 - lower air duct; 2 - air supply adjustment mechanism; 3 - fan; 4 - air supply duct; 5 - cable; 6 - connecting cuff; 7 - rear...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Similar sections of other Audi car models:
Body: Body elements Audi 80 B3 (1986-1991)
Body: Body elements Audi A6 C5 Allroad (1999-2005)

Share information:

100(C4, 1990-1994)

100(C4, 1990-1994, petrol)

100(C3, 1982-1990)

100(C3, 1982-1990, petrol)

100(C3, 1982-1990, diesel)