Car clutch repair Audi 100 C3, diesel
Clutch specifications
Type - Single-plate dry clutch, diaphragm spring with hydraulic or cable control depending on the model Clutch disc Diameter - 210 mm, 215 mm, 228 mm, or 240...
Type - Single-plate dry clutch, diaphragm spring with hydraulic or cable control depending on the model Clutch disc Diameter - 210 mm, 215 mm, 228 mm, or 240...
General description
All models with manual transmission are equipped with a single-plate dry clutch with a diaphragm spring. The unit consists of a steel cover that is bolted to...
All models with manual transmission are equipped with a single-plate dry clutch with a diaphragm spring. The unit consists of a steel cover that is bolted to...
Clutch — adjustment
1. Check clutch operation and adjustment at the intervals given in the Maintenance Section using the following procedure according to the clutch type. Cable...
1. Check clutch operation and adjustment at the intervals given in the Maintenance Section using the following procedure according to the clutch type. Cable...
Clutch cable — removal and installation
1. Disconnect the negative battery terminal. 2. Remove the pack shelf to gain access to the top end of the clutch pedal. 3. Loosen the 2 locknuts on the clutch...
1. Disconnect the negative battery terminal. 2. Remove the pack shelf to gain access to the top end of the clutch pedal. 3. Loosen the 2 locknuts on the clutch...
Clutch pedal — removal and installation
1. Disconnect the negative battery terminal. 2. Remove the interior trim to gain access to the part connections. 3. On models equipped with a cable-operated...
1. Disconnect the negative battery terminal. 2. Remove the interior trim to gain access to the part connections. 3. On models equipped with a cable-operated...
Clutch Master Cylinder — Removal and Installation
On models equipped with a hydraulically controlled clutch, the master cylinder is located inside the vehicle, near the clutch and brake pedals. Fluid is...
On models equipped with a hydraulically controlled clutch, the master cylinder is located inside the vehicle, near the clutch and brake pedals. Fluid is...
Clutch Master Cylinder — Overhaul
1. Remove the master cylinder from the vehicle as described in the previous Chapter . 2. Remove the dust cap from the master cylinder, remove the retaining...
1. Remove the master cylinder from the vehicle as described in the previous Chapter . 2. Remove the dust cap from the master cylinder, remove the retaining...
Clutch slave cylinder — removal and installation
1. From underneath the vehicle, remove the tension wire from the slave cylinder and from the hole in the cylindrical mounting pin on top of the transmission....
1. From underneath the vehicle, remove the tension wire from the slave cylinder and from the hole in the cylindrical mounting pin on top of the transmission....
Clutch slave cylinder — overhaul
1. Remove the slave cylinder from the vehicle as described in the previous Chapter. 2. Release the small retaining ring securing the rubber dust cap to the...
1. Remove the slave cylinder from the vehicle as described in the previous Chapter. 2. Release the small retaining ring securing the rubber dust cap to the...
Clutch — removal, inspection and installation
1. Access to the clutch can be gained by removing the engine ( Section 1 ), or by removing the manual transmission ( Section 6 ). If the engine does not...
1. Access to the clutch can be gained by removing the engine ( Section 1 ), or by removing the manual transmission ( Section 6 ). If the engine does not...
Clutch release bearing and mechanism — removal, inspection and installation
1. With the transmission removed from the vehicle, proceed as follows according to type. Cable controlled clutch 2. The release bearing can be removed by...
1. With the transmission removed from the vehicle, proceed as follows according to type. Cable controlled clutch 2. The release bearing can be removed by...
Clutch hydraulic system — bleeding
1. If part of the hydraulic system has been dismantled, or if air has accidentally entered the system, it must be bled. The presence of air in the system is...
1. If part of the hydraulic system has been dismantled, or if air has accidentally entered the system, it must be bled. The presence of air in the system is...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections of other Audi car models:
Transmission: Clutch Audi 80 B3 (1986-1991, petrol)
Transmission: Clutch and drive shafts Audi A3 Type 8L (1996-2003)
Transmission: Clutch Audi A4 B7 (2004-2008)
Transmission: Clutch Audi A6 C5 Allroad (1999-2005)
Transmission: Clutch Audi A8 D2 (1994-2002)
Transmission: Clutch Audi 80 B3 (1986-1991, petrol)
Transmission: Clutch and drive shafts Audi A3 Type 8L (1996-2003)
Transmission: Clutch Audi A4 B7 (2004-2008)
Transmission: Clutch Audi A6 C5 Allroad (1999-2005)
Transmission: Clutch Audi A8 D2 (1994-2002)
Share information:
- General information
- User manual
- Power unit
- Engine repair
- Ignition system
- Fuel system (gasoline)
- Fuel system (diesel)
- Lubrication system
- Cooling system
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Drive shafts
- Chassis
- Car suspension
- Steering
- Wheels and tires
- Brake system
- Body
- Ventilation and heating
- Body repair
- Electrical equipment
- Power devices
- Lighting and appliances
- Electrical circuits
- General information
- Operation and maintenance
- Power unit
- Engine repair
- Exhaust system
- Cooling system
- Supply system
- Air filter
- Mono-Motronic injection system
- Digifant injection system
- KE-III-Jetronic and KE-Motronic
- MPI and MPFI injection system
- Transmission
- Clutch
- Car gearbox
- Chassis
- Suspension and steering
- Brake system
- Wheels and tires
- Body
- Exterior
- Interior
- Electrical equipment
- Fuses and relays
- Power devices
- Ignition system
- Lighting and signaling
- Equipment and devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Specifications
- Power unit
- Engines 4-cylinder
- Engines 5-cylinder
- Diesel engine
- Cooling system
- Power system (carburetor)
- Power system (injector)
- Fuel system (diesel)
- Transistor ignition system
- Electronic ignition system
- Transmission
- Clutch
- 4 speed gearbox 014
- 5 speed gearbox 013 and 093
- 5 speed gearbox 016 and 012
- Shift mechanism KP 016
- Automatic transmission
- Front wheel drive
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body
- Body elements
- Electrical equipment
- Lighting and appliances
- Power devices
- Electrical circuits
- General information
- Maintenance and operation
- 4 cylinder engine
- Engine repair
- Cooling and lubrication system
- Supply system
- Ignition system
- 5 cylinder engine
- Engine repair
- Cooling and lubrication system
- Supply system
- Ignition system
- Transmission
- Clutch and drive shafts
- 4 speed gearbox 014
- 5 speed gearbox 013 and 093
- 5 speed gearbox 016 and 012
- Automatic gearbox
- Chassis
- Steering
- Front suspension
- Rear suspension
- Brake system
- Body
- Body elements
- Doors, locks and windows
- Body repair
- Electrical equipment
- Equipment and devices
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Troubleshooting
- Power unit
- Engine in a car
- Engine removed
- Cooling system
- Fuel system
- Exhaust system
- Starting and charging
- Preheating
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis
- Brake system
- Suspension
- Steering
- Body
- Exterior
- Interior
- Electrical equipment
- Equipment and devices
- Electrical circuits