Detailed specifications of the braking system Service brake system with hydraulic drive, consisting of two independent circuits for braking the front and rear wheels diagonally (left front - right rear,...
Tightening torques for main threaded connections Tightening torques of the main threaded connections, kgf·m Front wheel brakes Girling Brake Caliper Bolt: 3.5. Bolt of fastening of a directing finger of a...
Front wheel brake parts Details of the brake mechanism of the front wheel brand ATE: 1 - protective cover; 2 - solid brake disc; 3 - ventilated brake disc; 4 - brake pads; 5 -...
Rear wheel brake mechanism Rear wheel brake: 1 - lock washers of the guide springs of the pads; 2 - lower coupling spring; 3 - parking brake cable; 4 - spring of the device for automatic...
Replacing the front brake pads ATE Raise the front of the car, put it on stands and remove the wheels. Carry out the following operations on both sides of the vehicle. Replacing the brake pads...
Girling Front Brake Pad Replacement Raise the front of the car, put it on stands and remove the front wheels. Carry out the following operations on both sides of the vehicle. Replacing the brake...
Removal and installation of a brake disk Raise the front of the car, put it on stands and remove the front wheels. Remove the brake pads as above. Loosen two screws 1 (see photo) fastening the guide...
Replacing the drum brake pads of the rear wheels Withdrawal Raise the rear of the car. put on stands and remove the rear wheels. Carry out the following operations on both sides of the vehicle. Rear brake...
Parking brake adjustment Parking brake adjustment is only necessary when replacing the handbrake cable or linkage, as the rear brakes have a device to automatically adjust the...
Replacing the rear disc brake pads Raise the rear of the car. place on supports and remove the rear wheels Perform the following operations on both sides of the car. Replacing the rear disc...
Removal and installation of a back brake disk Raise the rear of the vehicle, place it on stands and remove the rear wheels. Rear brake disc: 1 - until January 1988; 2 - since January 1988 Remove the brake...
Adjusting the operation of the disc parking brake Warning. When adjusting the parking brake cable must not be under tension. Vehicles without body positioner Use a screwdriver to press the lever of the parking...
Pressure regulator leak test Unscrew the air outlet fittings from the brake caliper of the left front wheel and from the wheel cylinder (on vehicles with rear drum brakes) or from a...
Checking the air pressure in the pressure accumulator The pressure accumulator is installed only on vehicles with hydraulic brake booster. With the engine off, press the brake pedal approximately 20 times. Unscrew...
Checking the Battery Relief Valve Attach a control pressure gauge in the same way as for checking the air pressure in the pressure accumulator. Let the engine idle until the maximum pressure in...
Removal of air from a hydraulic drive of brakes Bleeding the brakes is necessary to remove air from the hydraulic drive. Air can get into the hydraulic drive due to depressurization of the system during the...
The principle of operation of the ABS system The braking system works most effectively when the tire has maximum friction on the road surface. To brake, the tire must transfer a certain amount of friction...
Features of the ABS system device The ABS consists mainly of wheel pulse generators, a hydraulic unit and an electronic control unit. The impulse generator consists of a gear wheel mounted on...
ABS system operation As soon as the wheel slows down or begins to slip, which indicates the beginning of its blocking, the solenoid valve, by signals from the electronic control...
Precautions for vehicles with ABS In the case of removing the battery for the production of electric welding robots, it is necessary to disconnect the plug connector from the electronic control...
Removal and installation of the hydroblock Withdrawal Disconnect the wire from the negative battery terminal. Remove the brake fluid from the reservoir with a syringe. Disconnect the pipelines from the...
Removal and installation of wheel speed sensors Remove the wheel from the desired side. Loosen the sensor mounting bolt. The arrow shows the wheel speed sensor Disconnect the block from the sensor (when...