Body. General information Body AUDI 80/90 has a supporting structure. The bottom, sides, roof and rear fenders are welded together. Major damage to the body can only be repaired in a...
Removal and installation of a forward bumper 1 guide piece 2 latch 3 self-tapping screw 4 overlay 5 cylinder head bolt, 23 Nm 6 washer 7 bumper AUDI 80 8 bracket 9 bracket 10 distance sliding element...
Removal and installation of a back bumper Note: Removal and installation is carried out in the same way as on the front bumper. 1 - guide piece Press ends of bumper downwards -arrow C- and out of...
Removal and installation of a forward facing The front cladding consists of four parts: the middle and lower parts, the right and left locking crossbars. Describes the removal of the cladding in the kit....
Removal and installation of front fenders Withdrawal Remove the front bumper. Remove locker. Remove sealing tape. Open the hood. Left fender: remove the hood stop from the rubber nozzle and knock out...
Removal and installation of a cowl Withdrawal Disconnect the hose at the washer nozzle. Remove hinge cover -1-. Mark the installation position of the bonnet by marking around the bolts -2- with...
Trunk lid adjustment Sedan 1 - bracket 2 - gas-filled spring stop 3 - bolt, 21 Nm 4 - nut, 21 Nm Loosen to adjust size. Trunk lid/wing: 4.4+1 mm; trunk lid/rear window: 6.5+1 mm. 5...
Trunk lid lock Sedan 1 - nut, 6 Nm 2 - spring washer 3 - hinge sleeve 4 - drive rod Adjustment: insert the ends of the rod and tighten the rod by selecting the gap on the...
Removal and installation/adjustment of doors Withdrawal Remove doorway. Unscrew the door and remove it. Pre-mark the installation position, for which circle the heads of the bolts with a felt-tip pen....
Door trim 1 - window opening handle Lubricate the screw with a locking agent, for example VAG AMW 197 OOO 001. 2 - lower part of the armrest During installation, the...
Removal and installation of the door lock Withdrawal Remove inner door trim. Pull the rod out of the opening lever. Disconnect the door release cable. To do this, unfasten the cable and unscrew it from...
Door handle 1 - swivel bracket 2 - screw, 3 Nm 3 - door handle 4 - overlay 5 - lock washer 6 - actuating lever with articulated sleeve 7 - spring 8 - sealing ring 9 - lock...
Removal and installation of a door frame Sedan only Withdrawal Remove inner door trim. Unclip cable to open door from inside. Disconnect connector for power window. Lower the glass a little. Mark...
Door window glass adjustment Sedan only 1 - adjustable window stop B - the area of adjacent glass to the inner sealing sponge Attention: Adjust the glass with the door closed. The figure...
Mirror glass replacement The glass of the mirror is only latched, regardless of whether the mirror is mechanically or electrically operated. Tape the edges of the case with adhesive...
Removal and installation of an external mirror Withdrawal Attention: Outside mirror with electrical installation: unscrew the mirror base and disconnect the connector directly at the base. Remove inner door...
Adjustment of the adjusting mechanism of a mirror Adjustment of the mirror setting mechanism should be carried out when the mirror installation is difficult or too easy. The idle handle or setting disc must...
Removal and installation of the lower left overlay Withdrawal If equipped, remove the starter pull handle. To do this, press the protrusion with a screwdriver from below through the hole and remove the handle....
Central locking device The central locking device consists of a supply pump, connections and actuating elements of individual locks. The electric pump creates an increased pressure...
Cleaning drain hoses Vehicles with a sliding sunroof have drain hoses that allow water to drain to the outside. Clogged drain hoses are best cleared with an old speedometer flex...