Engine 5-cylinder car Audi 80 B3, petrol
Engine specifications
General information Working volume: 2.0 l - 1994 cm³ 2.2 l - 2226 cm³ 2.3 l - 2309 cm³ Cylinder Bore/Piston Stroke: 2.0 l - 81.0/77.4 mm 2.2 l - 81.0/86.4 mm...
General information Working volume: 2.0 l - 1994 cm³ 2.2 l - 2226 cm³ 2.3 l - 2309 cm³ Cylinder Bore/Piston Stroke: 2.0 l - 81.0/77.4 mm 2.2 l - 81.0/86.4 mm...
General description of the engine
The engine is a 5 - cylinder, in-line, overhead camshaft, traditionally mounted on the front side of the car. The crankshaft has six bearings, main bearing...
The engine is a 5 - cylinder, in-line, overhead camshaft, traditionally mounted on the front side of the car. The crankshaft has six bearings, main bearing...
Basic actions possible with the engine
Maintenance Cm. Part A, Chapter 2 . The oil filter is located on the right side of the engine (photo). In the car Cm. Part A, Chapter 3 . But note that on a...
Maintenance Cm. Part A, Chapter 2 . The oil filter is located on the right side of the engine (photo). In the car Cm. Part A, Chapter 3 . But note that on a...
Engine — removal and installation
1. Remove the hood as described in Section 11 . 2. Disconnect the negative battery cable. 3. Unscrew and remove the mudguard from under the engine. 4. Place a...
1. Remove the hood as described in Section 11 . 2. Disconnect the negative battery cable. 3. Unscrew and remove the mudguard from under the engine. 4. Place a...
Camshaft and hydraulic tappets — removal
Note: If the engine is in the vehicle, first do the following: (a) Disconnect the negative battery cable (b) Remove the air filter and fuel injection system...
Note: If the engine is in the vehicle, first do the following: (a) Disconnect the negative battery cable (b) Remove the air filter and fuel injection system...
Cylinder head — removal
Note: If the engine is in the vehicle, first do the following: (a) Disconnect the negative battery cable (b) Drain the cooling system ( Section 2 ) (c) Remove...
Note: If the engine is in the vehicle, first do the following: (a) Disconnect the negative battery cable (b) Drain the cooling system ( Section 2 ) (c) Remove...
Cylinder head — overhaul
1. Follow the procedures given in Part A, Chapter 13 , but note the following. 2. On a 10 - valve engine, intake valves are 2 - 4-5 - 7-9, exhaust valves are 1...
1. Follow the procedures given in Part A, Chapter 13 , but note the following. 2. On a 10 - valve engine, intake valves are 2 - 4-5 - 7-9, exhaust valves are 1...
Cylinder head — installation
1. Make sure the top of the block is completely clean, then position the new gasket on it, with the part number or "OBEN TOP" mark facing up. 2. Check that the...
1. Make sure the top of the block is completely clean, then position the new gasket on it, with the part number or "OBEN TOP" mark facing up. 2. Check that the...
Camshaft and hydraulic tappets installation
Note: If necessary, temporarily install the camshaft and check the camshaft side play before installing the hydraulic lifters ( see Specifications ). 1....
Note: If necessary, temporarily install the camshaft and check the camshaft side play before installing the hydraulic lifters ( see Specifications ). 1....
Timing Belt and Sprockets — Removal and Installation
Note: If the engine is in the vehicle, first do the following: (a) Disconnect the negative battery cable (b) Where used, remove the power steering pump leaving...
Note: If the engine is in the vehicle, first do the following: (a) Disconnect the negative battery cable (b) Where used, remove the power steering pump leaving...
Flywheel/drive disc — removal, inspection and installation
1. The procedure is similar to that described in Part A, Chapter 14 , but note the position of the flywheel/drive plate relative to the crankshaft, as the...
1. The procedure is similar to that described in Part A, Chapter 14 , but note the position of the flywheel/drive plate relative to the crankshaft, as the...
Pallet — removal and installation
See Part A, Chapter 16 , but on a 20 valve engine remove the dipstick and crank the engine until the fuse parts in the pan and flywheel are aligned to remove...
See Part A, Chapter 16 , but on a 20 valve engine remove the dipstick and crank the engine until the fuse parts in the pan and flywheel are aligned to remove...
Front and rear crankshaft seals — replacement
Front oil seal 1. Remove the timing belt and crankshaft sprocket as described in Chapter 40 . 2. If you have a special tool, the seal can be replaced without...
Front oil seal 1. Remove the timing belt and crankshaft sprocket as described in Chapter 40 . 2. If you have a special tool, the seal can be replaced without...
Oil pump — removal, inspection and installation
1. Remove the timing belt and crankshaft sprocket as described in Chapter 40 . 2. Remove the tray as described in Chapter 42 . 3. Remove the oil dipstick. 4....
1. Remove the timing belt and crankshaft sprocket as described in Chapter 40 . 2. Remove the tray as described in Chapter 42 . 3. Remove the oil dipstick. 4....
Pistons and connecting rods — removal and disassembly
See Part A, Chapter 19 from this Section. Removing the cylinder head is described in Chapter 36 , removing the toothed drive belt - in Chapter 40 . Instead of...
See Part A, Chapter 19 from this Section. Removing the cylinder head is described in Chapter 36 , removing the toothed drive belt - in Chapter 40 . Instead of...
Pistons and connecting rods — assembly and installation
See Part A, Chapter 21 from this Section. After installing the pistons, install the oil suction tube with a new gasket, tighten the bolts and bend the lock...
See Part A, Chapter 21 from this Section. After installing the pistons, install the oil suction tube with a new gasket, tighten the bolts and bend the lock...
Crankshaft — removal, inspection and installation
1. With the engine removed from the vehicle, remove the pistons and connecting rods as described in Chapter 45 . 2. Remove the oil pump ( Chapter 44 ) and rear...
1. With the engine removed from the vehicle, remove the pistons and connecting rods as described in Chapter 45 . 2. Remove the oil pump ( Chapter 44 ) and rear...
Troubleshooting engine problems
The engine does not start The battery is discharged Loose battery connections The ignition wiring is loose or broken Moisture on spark plugs, distributor cap,...
The engine does not start The battery is discharged Loose battery connections The ignition wiring is loose or broken Moisture on spark plugs, distributor cap,...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections of other Audi car models:
Power unit: Engines 5-cylinder Audi 100 C3 (1982-1990)
Gasoline engines: 5 cylinder engines Audi A6 C4 (1994-1997)
Power unit: Engines 5-cylinder Audi 100 C3 (1982-1990)
Gasoline engines: 5 cylinder engines Audi A6 C4 (1994-1997)
Share information:
- General information
- User manual
- Maintenance
- Troubleshooting
- Power unit
- Engine
- Cooling system
- Heating and ventilation
- Petrol injection
- Diesel fuel system
- Fuel system
- Exhaust systems
- Ignition system
- Transmission
- Clutch
- Car gearbox
- Chassis
- Brake system
- Suspension and steering wheel
- Body
- Body and trim
- Electrical equipment
- Electrical system
- Electrical circuits
- General information
- Repair characteristics
- Maintenance
- Power unit
- Gasoline engine
- Diesel engine
- Engine lubrication system
- Fuel system (gasoline)
- Injection system (gasoline)
- Fuel system (diesel)
- Ignition system
- Cooling system
- Heater
- Exhaust system
- Transmission
- Clutch and gearbox
- Chassis
- Steering
- Brake system
- Car suspension
- Body
- Body elements
- Electrical equipment
- Power devices
- Lighting and appliances
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Engine 4-cylinder
- Engine 5-cylinder
- Cooling system
- Fuel and exhaust systems
- Ignition system
- Transmission
- Clutch
- Mechanical transmission
- Automatic transmission
- Drive shafts
- Chassis
- Brake system
- Suspension
- Steering
- Body
- Exterior
- Interior
- Electrical equipment
- Equipment and devices
- Electrical circuits