External elements of the car body Audi 80 B3, petrol
Body specifications
Tightening torque, Nm Door hinge bolt - 30 Window lifter fastener - 20 Door lock - 16 Impact plate pin - 50 Bumpers - 23 Seat belts: Inertia Drum Mounting Bolt...
Tightening torque, Nm Door hinge bolt - 30 Window lifter fastener - 20 Door lock - 16 Impact plate pin - 50 Bumpers - 23 Seat belts: Inertia Drum Mounting Bolt...
General description of the body
The body is a steel, all-welded structure, actively treated on all sides for effective protection against corrosion. All panels are galvanized and hot wax is...
The body is a steel, all-welded structure, actively treated on all sides for effective protection against corrosion. All panels are galvanized and hot wax is...
Body maintenance
Perform the following procedures, at intervals given in " Current maintenance " at the beginning of the guide. Check and adjust the air conditioning compressor...
Perform the following procedures, at intervals given in " Current maintenance " at the beginning of the guide. Check and adjust the air conditioning compressor...
Body and subframe — maintenance
The condition of your car's body is very important because it affects its resale value. It is much more difficult to restore a poorly maintained or damaged...
The condition of your car's body is very important because it affects its resale value. It is much more difficult to restore a poorly maintained or damaged...
Repair of minor body damage
Note: For more detailed information on body repair, see the book "Body Repair Guide". Repair of minor scratches in the body structure If the scratch is...
Note: For more detailed information on body repair, see the book "Body Repair Guide". Repair of minor scratches in the body structure If the scratch is...
Body repair — serious damage
Where there is serious damage, replacement of parts and welding are necessary - leave it to the professionals. If the damage was caused by a collision, it is...
Where there is serious damage, replacement of parts and welding are necessary - leave it to the professionals. If the damage was caused by a collision, it is...
Hood — removal, installation and adjustment
1. Support the hood in the open position and place cardboard or rags under the corners. 2. Push the windshield washer jets back and remove them from the hood...
1. Support the hood in the open position and place cardboard or rags under the corners. 2. Push the windshield washer jets back and remove them from the hood...
Bonnet Lock Cable — Removal and Installation
1. From inside the vehicle, remove the lower trim panel from under the steering column. 2. Loosen the hood release lever mounting screws, then disconnect the...
1. From inside the vehicle, remove the lower trim panel from under the steering column. 2. Loosen the hood release lever mounting screws, then disconnect the...
Trunk lid — removal and installation
1. Support the trunk lid in the open position and place cardboard or rags under the corners of the hinges. 2. Disconnect the negative battery cable. 3....
1. Support the trunk lid in the open position and place cardboard or rags under the corners of the hinges. 2. Disconnect the negative battery cable. 3....
Trunk lid lock — removal and installation
1. Open the trunk lid and remove the plastic covers from the lock and trunk lid (photo). 2. Remove and disconnect the tie rod from the lock and lock cylinder....
1. Open the trunk lid and remove the plastic covers from the lock and trunk lid (photo). 2. Remove and disconnect the tie rod from the lock and lock cylinder....
Trunk lid and rear door pillar — removal and installation
1. Support the rear trunk lid in the open position. 2. On the trunk lid only, remove the hinges by knocking out the pins, then open the trunk lid all the way....
1. Support the rear trunk lid in the open position. 2. On the trunk lid only, remove the hinges by knocking out the pins, then open the trunk lid all the way....
Rear door — removal and installation
1. Hold the rear door open and place cardboard or rags under the corners of the hinges. 2. Disconnect the negative battery cable. 3. Remove the interior trim...
1. Hold the rear door open and place cardboard or rags under the corners of the hinges. 2. Disconnect the negative battery cable. 3. Remove the interior trim...
Rear door lock — removal and installation
1. Open the rear door and remove the trim from the inside. 2. Remove the cover from the lock. 3. Disconnect the lever linkage from the lock and lock cylinder....
1. Open the rear door and remove the trim from the inside. 2. Remove the cover from the lock. 3. Disconnect the lever linkage from the lock and lock cylinder....
External door handle — removal and installation
1. Remove the door trim panel ( Chapter 14 ). 2. Pull out the bracket and disconnect the linkage rod from the outer handle. 3. Loosen the handle mounting bolt,...
1. Remove the door trim panel ( Chapter 14 ). 2. Pull out the bracket and disconnect the linkage rod from the outer handle. 3. Loosen the handle mounting bolt,...
Doors — removal and installation
1. Remove the trim panel ( Chapter 14 ). 2. If it is necessary to remove the door, mark the hinges with a pencil (photo). 3. Disconnect all electrical wiring...
1. Remove the trim panel ( Chapter 14 ). 2. If it is necessary to remove the door, mark the hinges with a pencil (photo). 3. Disconnect all electrical wiring...
Windshield, rear window glass and rear door window glass — removal and installation
The windshield, rear window glass and rear door window glass are attached directly to the body. Their removal and installation requires the use of special...
The windshield, rear window glass and rear door window glass are attached directly to the body. Their removal and installation requires the use of special...
Hatch — removal, installation and adjustment
1. Move the hatch to an inclined position. 2. Press the pivot flap, then use a 300mm long hook to detach the flap tension springs. 3. Remove the flap notches,...
1. Move the hatch to an inclined position. 2. Press the pivot flap, then use a 300mm long hook to detach the flap tension springs. 3. Remove the flap notches,...
Hatch drain hoses — cleaning
1. If the hatch drains become clogged with accumulated dust, they can be cleared using the long internal speedometer drive cable, approximately 2300 mm long....
1. If the hatch drains become clogged with accumulated dust, they can be cleared using the long internal speedometer drive cable, approximately 2300 mm long....
Bumpers — removal and installation
1. Raise the front or rear of the vehicle and support it on axle stands. 2. Where equipped, remove the fog lamp as described in Section 12 . 3. Unfasten the...
1. Raise the front or rear of the vehicle and support it on axle stands. 2. Where equipped, remove the fog lamp as described in Section 12 . 3. Unfasten the...
Radiator grille — removal and installation
1. Open the hood and remove the two screws holding the radiator grille to the front edge (photo). 2. Using a screwdriver, carefully pry the grille off the...
1. Open the hood and remove the two screws holding the radiator grille to the front edge (photo). 2. Using a screwdriver, carefully pry the grille off the...
Outside mirror — removal and installation
1. Remove the door trim panel ( Chapter 14 ). Electrically operated mirror 2. Rotate the mirror 90° to expose the mounting screws (photo). 3. Loosen the...
1. Remove the door trim panel ( Chapter 14 ). Electrically operated mirror 2. Rotate the mirror 90° to expose the mounting screws (photo). 3. Loosen the...
Rear view mirror — removal and installation
1. Pull the mirror down to remove it from the mounting plate on the windshield. 2. To install the mirror, place it on the mounting plate at an angle between...
1. Pull the mirror down to remove it from the mounting plate on the windshield. 2. To install the mirror, place it on the mounting plate at an angle between...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections of other Audi car models:
Body: Exterior Audi 100 C4 (1990-1994, petrol)
Body: Exterior (external elements) Audi A3 Type 8L (1996-2003)
Body: Exterior Audi A4 B8 (2007-2015)
Body: Exterior Audi A6 C5 (1997-2004)
Body: Exterior (external elements) Audi A8 D2 (1994-2002)
Body: Exterior Audi Q5 Type 8R (2008-2017)
Body: Exterior Audi A2 (1999-2005)
Body: Exterior Audi 100 C4 (1990-1994, petrol)
Body: Exterior (external elements) Audi A3 Type 8L (1996-2003)
Body: Exterior Audi A4 B8 (2007-2015)
Body: Exterior Audi A6 C5 (1997-2004)
Body: Exterior (external elements) Audi A8 D2 (1994-2002)
Body: Exterior Audi Q5 Type 8R (2008-2017)
Body: Exterior Audi A2 (1999-2005)
Share information:
- General information
- User manual
- Maintenance
- Troubleshooting
- Power unit
- Engine
- Cooling system
- Heating and ventilation
- Petrol injection
- Diesel fuel system
- Fuel system
- Exhaust systems
- Ignition system
- Transmission
- Clutch
- Car gearbox
- Chassis
- Brake system
- Suspension and steering wheel
- Body
- Body and trim
- Electrical equipment
- Electrical system
- Electrical circuits
- General information
- Repair characteristics
- Maintenance
- Power unit
- Gasoline engine
- Diesel engine
- Engine lubrication system
- Fuel system (gasoline)
- Injection system (gasoline)
- Fuel system (diesel)
- Ignition system
- Cooling system
- Heater
- Exhaust system
- Transmission
- Clutch and gearbox
- Chassis
- Steering
- Brake system
- Car suspension
- Body
- Body elements
- Electrical equipment
- Power devices
- Lighting and appliances
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Engine 4-cylinder
- Engine 5-cylinder
- Cooling system
- Fuel and exhaust systems
- Ignition system
- Transmission
- Clutch
- Mechanical transmission
- Automatic transmission
- Drive shafts
- Chassis
- Brake system
- Suspension
- Steering
- Body
- Exterior
- Interior
- Electrical equipment
- Equipment and devices
- Electrical circuits