Diesel engines 3.0 liters of car Audi A4 B8

3.0L Diesel Engine — Removal
More details see previous engine . Remove the engine from the manual transmission The engine with gearbox and accessory bracket is removed downwards with the...

3.0L Diesel Engine Specifications
Technical specifications Letter designations CDUC CLAB CKVB Working volume, l 2,967 2,967 2,967 Power, kW at rpm 180/4000...4500 150/4000...4500...

Disconnecting the engine and manual transmission
Prepare the conductor "VAS 6131/13-7": Unscrew the "arrow" bolt on the conductor "VAS 6131/13-7" and remove support "1". The power unit is removed and...

3.0L Diesel Engine — Installation
Tightening torques (Nm) Bolts and nuts M6 9 M7 15 M8 20 M10 40 M12 65 Engine for manual transmission/multitronic CMV/dual clutch transmission 0B5 Pos. Bolt Nm...

3.0L Diesel Engine — Powertrain Support
Support of units 1. Bolt: 20 Nm. 2. Mounting plate: for engine mount; if the engine mount is defective, replace the mounting shield; check the mounting plate...

Cylinder block from the belt pulley side — poly V-drive
Poly V-belt drive 1. Poly V-belt: check the degree of wear; before removing, mark the direction of travel with chalk or a felt-tip pen; don't overdo it; when...

Cylinder block on the pulley side — lip seal and sealing flange on the poly V-belt pulley side
Lip seal and seal. flange on the side of the poly V-belt pulley 1. Bolt. 2. Sealing the crankshaft shaft on the side of the resolved pulley. 3. Oil radiator...

Cylinder block from the gearbox side — driven disk
Slave disk 1. Bolt: replace; 60 Nm + turn further by 90°. 2. Driven disk: Check the holes for cracks and entry holes. 3. Mounting pin. 4. Crankshaft. 5. Shaft...

Cylinder block — crankshaft
Crankshaft 1. Crankshaft. 2. Guide bushing: 4 pcs.; insert into the cylinder block. 3. Camshaft frame. 4. Bolt: replace. 5. Crankshaft axial locking liner:...

Cylinder block — pistons and connecting rods
Pistons and connecting rods 1. Screws: replace; lubricate the threads and mating surface with oil; 35 Nm + turn further by 90°. 2. Connecting rod cap: thanks...

Chain Drive — Timing Chain Covers
Timing chain covers 1. Bolt: replace. 2. Engine speed sensor ring gear "G28". 3. Shaft seal: for crankshaft on gearbox side. 4. Lower drive chain cover. 5....

Camshaft chain drive
Camshaft chain drive 1. Bolt: 9 Nm. 2. Protection against jumping. 3. Crankshaft: with camshaft drive chain sprocket. 4. Stabilizer bar: install in the proper...

Oil pump drive, high-pressure fuel pump and balance shaft
Oil drive. pump and fuel injection pump 1. Oil drive. pump and fuel injection pump. 2. Bolt: replace; 30 Nm + turn further by +45°. 3. Oil sprocket. pump;...

Cylinder head — cylinder head cover
Cylinder head cover Image of cylinder head cover from 2nd row of cylinders (left). 1. Gasket: cylinder head covers; if damaged or loose, replace. 2. Cylinder...

Cylinder head — removal and installation
Cylinder head Image of the cylinder head. from the 2nd row (from the left). 1. Cylinder head gasket; installation position: part number facing the cylinder...

Valve mechanism — removal and installation
Valve mechanism Image of the cylinder head. from the 2nd row (from the left). 1. Valve: cannot be machined, only lapping is allowed; mark mont. reinstallation...

Lubrication system — lower part of the oil pan and oil pump
Lower part of the oil. sump and oil. pump 1. Oil level and temperature sensor "G266". 2. Lip seal: replace. 3. Bolt: replace. 4. Lower part of the oil. pallet....

Lubrication system — upper part of the oil pan
Upper part of the oil. pallet 1. Bolt: 9 Nm. 2. Oil pressure regulating valve "N428". 3. Sealing ring: replace. 4. Upper part of the oil. pallet. 5. Lip seal:...

Lubrication system — oil filter housing, oil pressure sensor
Oil housing. filters, oil pressure sensor 1. Bolt: 9 Nm. 2. Oil housing. filter: with thermostat for engine cooling according to algorithm "F265"; replace...

Lubrication system — oil radiator, coolant shut-off valve
Oil radiator, coolant shut-off valve 1. Mounting plate gaskets. 2. Oil radiator mounting plate. 3. Bolt: 9 Nm. 4. Oil radiator gasket; replace. 5. Bolt: 9 Nm....

Cooling system — coolant hose connection diagram
Caution! Risk of burns from hot steam and hot coolant. When the engine is warm, the cooling system is under excess pressure. To relieve excess pressure, place...

Cooling system — water pump and coolant supply pipes
Water pump 1. Bolt: tighten in a crosswise pattern in stages; 9 Nm. 2. Belt drive pulley for water pump; installation position: the inscription "vorne" (front)...

Cooling system — coolant shut-off valve and coolant temperature sensor
Coolant shut-off valve 1. Oil mounting plate. radiator and coolant shut-off valve. 2. Gasket: replace. 3. Bolt: 9 Nm. 4. Cooling system hose. 5. Coolant supply...

Cooling system — radiator and radiator fan
Radiator and radiator fan 1. Latches. 2. Coolant temperature sensor at the radiator outlet "G83". 3. Air duct. 4. Cooling system hose: to remove, release the...

Cooling system — fan frame and radiator fan
Fan frame and radiator fan 1. Radiator fan "V7": with fan control unit "J293". 2. Radiator fan 2 "V177": with control unit 2 for radiator fan -J671-. 3. Fan...

Turbocharger — removal and installation
Turbocharger 1. Gasket: replace. 2. Turbocharger bracket. 3. Bolt: tighten crosswise to 23 Nm in several steps. 4. Studs: Replace after each loosening of the...

Charge air cooling
Charge air cooling 1. Charge air cooler. 2. Hose clamp. 3. Air duct hose: to intercooler: must be cleaned of oil and grease before installation. 4. Hose clamp....

Injection system — component installation locations
Overview of installation locations Engine compartment 1. Air flow meter "G70". 2. Electrical connector of the temperature sensor in the system. exhaust gas...

Injection system — schematic overview of the fuel system and vacuum system
Schematic overview of fuel. syst. 1. Fuel metering valve "N290": do not open. 2. Fuel injection pump. 3. Fuel rail: cylinder bank 1 (right). 4. Fuel pressure...

Injection system — air filter
Air filter 1. Air duct: clean from salt deposits, dirt and leaves. 2. Sealing element. 3. Rubber tip of the air housing. filter. 4. Air housing. filter: clear...

Injection system — intake manifold
Intake manifold 1. Air guide pipe bracket. 2/3. Bolt: 9 Nm. 4. Gasket: replace. 5/6. Bolt: 9 Nm. 7. Intake manifold flap motor "V157". 8. Gasket: replace. 9....

Injection system — high pressure pump
High pressure pump 1. Nut: to unscrew, hold the adapter "pos. 2" with the support "T40248"; 70 Nm. 2. Fuel injection pump chain sprocket adapter; to unscrew...

Injection system — injection modules (nozzles)
Injection modules (nozzles) 1. Clamp bracket support: different tightening torques: on the camshaft bearing 2.5 Nm, on the cylinder head 9 Nm. 2. Clamp: For...

Exhaust system — muffler and diesel particulate filter
Muffler 1. Y-pipe: Factory installed as one piece with the rear mufflers; in case of repair of the tee, main muffler and muffler end, replace them separately....

Exhaust system — exhaust manifold and exhaust gas recirculation system
Exhaust manifold Image of the exhaust manifold from row 2 (left) 1. Nut: replace; lubricate the threads with heat-resistant paste; 25 Nm. 2. Exhaust manifold....

Pre-heating device
The pre-heating system is controlled by the glow plug control unit "J179." The control unit features a self-diagnostic function. If the pre-heating device...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

A4(B8, 2007-2015)

A4(B7, 2004-2008)

A4(B6, 2000-2006)

A4(B6, 2000-2006, petrol)

A4(B5, 1994-2001)

A4(B5, 1994-2001, petrol)