Doors, locks and windows of the car Audi A2
Removal and installation, adjustment of the trunk lid and trunk lid lock
1. Trunk lid. Remove the trunk lid trim. Disconnect the plug connectors and remove them from the lid. Remove the gas struts from the lid side. Unscrew the Torx...
1. Trunk lid. Remove the trunk lid trim. Disconnect the plug connectors and remove them from the lid. Remove the gas struts from the lid side. Unscrew the Torx...
Removal and installation the trunk lock bracket
The rear panel trim is removed. Unscrew the hex nuts "1" and remove the trunk lid lock bracket. When installing, fit the lock bracket and loosely tighten the...
The rear panel trim is removed. Unscrew the hex nuts "1" and remove the trunk lid lock bracket. When installing, fit the lock bracket and loosely tighten the...
Removal and installation the trunk gasket
To remove, remove gasket "1". When installing, press it into the body edges around the circumference.
To remove, remove gasket "1". When installing, press it into the body edges around the circumference.
Removal and installation the front door mounting bracket
1. Bracket of built-in door parts. After each dismantling of the bracket of built-in door parts, seal the cable guide of the outside mirror with butyl cord...
1. Bracket of built-in door parts. After each dismantling of the bracket of built-in door parts, seal the cable guide of the outside mirror with butyl cord...
Removal and installation the front door and the bracket for the built-in door parts
1. Front door. For clarity, the front door/mounting bracket seal is not shown in the illustration. Seal (sealing strips made of polyurethane foam) front...
1. Front door. For clarity, the front door/mounting bracket seal is not shown in the illustration. Seal (sealing strips made of polyurethane foam) front...
Gaps for adjusting the front doors
1. Bracket of built-in door parts. Size "a" = 5 mm + 1.5 mm. Adjust size "a" using the auxiliary template. Size "b" = 5 mm. 2 mm. Size "c" = 9.5 mm±1 mm. Size...
1. Bracket of built-in door parts. Size "a" = 5 mm + 1.5 mm. Adjust size "a" using the auxiliary template. Size "b" = 5 mm. 2 mm. Size "c" = 9.5 mm±1 mm. Size...
Removal and installation the front door opening limiter
1. Front door 2. Door opening limiter. Before removing, remove the door trim and the lower trim of the A-pillar. To remove, unscrew the hex nuts and bolts...
1. Front door 2. Door opening limiter. Before removing, remove the door trim and the lower trim of the A-pillar. To remove, unscrew the hex nuts and bolts...
Removal and installation the window lifter and door glass
1. Bracket for built-in door parts 2. Door glass. Loosen the bolt and open the hinge. Remove the glass downwards from the guides. Installation: Insert the...
1. Bracket for built-in door parts 2. Door glass. Loosen the bolt and open the hinge. Remove the glass downwards from the guides. Installation: Insert the...
Front door handle and lock
1. Door lock. Can be removed without dismantling the bracket of the built-in door parts 2. Door handle fastening. Before removing, dismantle the door handle....
1. Door lock. Can be removed without dismantling the bracket of the built-in door parts 2. Door handle fastening. Before removing, dismantle the door handle....
Removal the lock cylinder and the front door handle
1. Door lock cylinder. Pull the handle outward and hold it in this position. Unscrew the bolt "arrow C" counterclockwise with the socket wrench "T10072" until...
1. Door lock cylinder. Pull the handle outward and hold it in this position. Unscrew the bolt "arrow C" counterclockwise with the socket wrench "T10072" until...
Installing the front door handle
Install the door handle through the cutout in the door leaf. In this case, the seal on the door handle "1" must be placed behind the door leaf so that the...
Install the door handle through the cutout in the door leaf. In this case, the seal on the door handle "1" must be placed behind the door leaf so that the...
Removal the front door lock
1. Front door lock. Remove the door trim. Remove the mounting bracket. Disconnect the drive rod from the door handle. Unscrew the combination bolts. Pull the...
1. Front door lock. Remove the door trim. Remove the mounting bracket. Disconnect the drive rod from the door handle. Unscrew the combination bolts. Pull the...
Installing a front door lock
If the old door lock is being installed, it is necessary to remove the drive rod "2" from the drive lever "1" from above. If a new door lock is being...
If the old door lock is being installed, it is necessary to remove the drive rod "2" from the drive lever "1" from above. If a new door lock is being...
Removal and installation the pressure plate and glass guide
1. Bracket for built-in door parts 2. Glass guide. Remove the door glass before dismantling. To remove, remove the glass guide from the side of the door...
1. Bracket for built-in door parts 2. Glass guide. Remove the door glass before dismantling. To remove, remove the glass guide from the side of the door...
Removal and installation the outer seal of the front door
To remove, detach from the door from below and remove from the bracket of the built-in door parts from above. When installing, first position the rubber corner...
To remove, detach from the door from below and remove from the bracket of the built-in door parts from above. When installing, first position the rubber corner...
Removal and installation the front door inner seal
To dismantle, remove from the door flange. Before installation, remove the lower trim of the A-pillar and B-pillar. When installing, first fix the gasket "1"...
To dismantle, remove from the door flange. Before installation, remove the lower trim of the A-pillar and B-pillar. When installing, first fix the gasket "1"...
Front door seal and front door mounting bracket
Front Door/Mounting Bracket Seal (mounting shield) and the cable guide of the outside mirror in the bracket of the built-in door parts. Instructions. It is...
Front Door/Mounting Bracket Seal (mounting shield) and the cable guide of the outside mirror in the bracket of the built-in door parts. Instructions. It is...
Removal and installation the rear door mounting bracket
1. Bracket for built-in door parts 2. Mounting bracket (mounting plate) 3. Bolt Torgx, M6x1b, 11 pieces, 10 Nm. Consider the different length and diameter of...
1. Bracket for built-in door parts 2. Mounting bracket (mounting plate) 3. Bolt Torgx, M6x1b, 11 pieces, 10 Nm. Consider the different length and diameter of...
Removal and installation the rear door and built-in parts bracket
1. Rear door. For better clarity, the rear door seal/mounting bracket is not shown in the figure. Seal (sealing strips made of polyurethane foam)rear...
1. Rear door. For better clarity, the rear door seal/mounting bracket is not shown in the figure. Seal (sealing strips made of polyurethane foam)rear...
Rear door adjustment gaps
1. Bracket of built-in door parts. Size "a" = 4.5 mm + 1.5 mm. Adjust size "a" using the auxiliary template. Size "b" = 5 mm. 2 mm. Size "c" = 9.5 mm±1 mm....
1. Bracket of built-in door parts. Size "a" = 4.5 mm + 1.5 mm. Adjust size "a" using the auxiliary template. Size "b" = 5 mm. 2 mm. Size "c" = 9.5 mm±1 mm....
Removal and installation the rear door opening limiter
1. Back door 2. Door opening limiter. Before removing, remove the door trim and the lower trim of the A-pillar. To remove, unscrew the Allen nuts and bolts...
1. Back door 2. Door opening limiter. Before removing, remove the door trim and the lower trim of the A-pillar. To remove, unscrew the Allen nuts and bolts...
Removal and installation the rear window lifter and door glass
1. Bracket for built-in door parts 2. Door glass. Loosen the bolts and remove the glass from the support strip. Remove the glass downwards from the guides....
1. Bracket for built-in door parts 2. Door glass. Loosen the bolts and remove the glass from the support strip. Remove the glass downwards from the guides....
Rear door handle and lock
1. Door lock. Before removing, remove the bracket of the built-in door parts 2. Door handle fastening. Before removing, dismantle the door handle. To remove,...
1. Door lock. Before removing, remove the bracket of the built-in door parts 2. Door handle fastening. Before removing, dismantle the door handle. To remove,...
Removal and installation the rear door lock
1. Back door 2. Rear door lock. Remove the door trim. Remove the mounting bracket. Remove the door handle. Remove the door integrated parts bracket. Unscrew...
1. Back door 2. Rear door lock. Remove the door trim. Remove the mounting bracket. Remove the door handle. Remove the door integrated parts bracket. Unscrew...
Removal and installation the clamping strip and the rear door glass guide
1. Bracket for built-in door parts 2. Glass guide. Remove the door glass before dismantling. To remove, pull out the glass guide from the side of the door...
1. Bracket for built-in door parts 2. Glass guide. Remove the door glass before dismantling. To remove, pull out the glass guide from the side of the door...
Removal and installation the outer rear door seal
To remove, detach from the door -1. from below and remove from the bracket of the built-in door parts from above. When installing, first position the rubber...
To remove, detach from the door -1. from below and remove from the bracket of the built-in door parts from above. When installing, first position the rubber...
Removal and installation the rear door inner seal
To dismantle, remove from the door flange. Before installing, remove the lower trim of the B-pillar and the C-pillar. When installing, first fix the gasket "1"...
To dismantle, remove from the door flange. Before installing, remove the lower trim of the B-pillar and the C-pillar. When installing, first fix the gasket "1"...
Rear Door and Rear Door Mounting Bracket Seal
Instructions. It is necessary to use the set "Fasteners and gaskets for the mounting plate", All new spare doors after varnishing must be equipped with all the...
Instructions. It is necessary to use the set "Fasteners and gaskets for the mounting plate", All new spare doors after varnishing must be equipped with all the...
Removal and installation a lift-and-slide sunroof
1. Hatch frame 2. Sliding frame 3. Fairing 4. Cover "2" 5. Cover "3" 6. Gate valve 7. Hatch panel motor 8. Bolt Tough, 4 Nm 9. Fixing hooks 10. Hatch...
1. Hatch frame 2. Sliding frame 3. Fairing 4. Cover "2" 5. Cover "3" 6. Gate valve 7. Hatch panel motor 8. Bolt Tough, 4 Nm 9. Fixing hooks 10. Hatch...
Removal the lift-and-slide sunroof
1. Sunroof frame. Remove the headliner and sunroof protective frame. Open the sunroof fully rearward. Loosen the bolts. Loosen the nuts. Loosen the hexagonal...
1. Sunroof frame. Remove the headliner and sunroof protective frame. Open the sunroof fully rearward. Loosen the bolts. Loosen the nuts. Loosen the hexagonal...
Sealing of a lift and slide hatch
1. Lower sealing strip. Replace 2. Outer guide seal. Replace 3. Foil strip. Replace. Adhesion area: in the fold area from the front edge of the trunk door...
1. Lower sealing strip. Replace 2. Outer guide seal. Replace 3. Foil strip. Replace. Adhesion area: in the fold area from the front edge of the trunk door...
Removal the rear cover of the sliding and tilting sunroof
Before removing the rear cover, it is necessary to mark its position on the left and right on the frame of the sliding hatch "arrow". Remove the seal from the...
Before removing the rear cover, it is necessary to mark its position on the left and right on the frame of the sliding hatch "arrow". Remove the seal from the...
Removal and installation the guides of the lift-and-slide sunroof
Removal Remove the cables from the frame together with the link guides in the rear direction. Remove the remains of old grease from the guides of the sliding...
Removal Remove the cables from the frame together with the link guides in the rear direction. Remove the remains of old grease from the guides of the sliding...
Installing the rear cover of the sliding and lifting sunroof
Treat the bonding surfaces of the "arrow" of the sliding sunroof frame "1" and the rear cover with cleaner D 009 401 04. Apply primer D 009 200 02 to the...
Treat the bonding surfaces of the "arrow" of the sliding sunroof frame "1" and the rear cover with cleaner D 009 401 04. Apply primer D 009 200 02 to the...
Installation of a lift and slide hatch
Installation of the mounting device for the hatch "VAS 60101" 1. Sunroof mounting device "VAS 6010". After the sunroof has been inserted into the opening, it...
Installation of the mounting device for the hatch "VAS 60101" 1. Sunroof mounting device "VAS 6010". After the sunroof has been inserted into the opening, it...
Removal and installation the hatch cover
Instructions. Cover "1" and cover "4" are glued to the roof and are not spare parts. If the engine is faulty, the hatch is driven by an emergency drive....
Instructions. Cover "1" and cover "4" are glued to the roof and are not spare parts. If the engine is faulty, the hatch is driven by an emergency drive....
Removal and installation the hatch locking hooks
Detach the protective frame in the area of the bolts. To remove the locking hook, unscrew the bolts "arrows" and remove the hook from the frame. Insert the...
Detach the protective frame in the area of the bolts. To remove the locking hook, unscrew the bolts "arrows" and remove the hook from the frame. Insert the...
Removal and installation the sliding frame
Open cover "2" and cover "3". Through the open roof, press the sliding frame from the side into the guides. On the opposite side, squeeze the spring-loaded...
Open cover "2" and cover "3". Through the open roof, press the sliding frame from the side into the guides. On the opposite side, squeeze the spring-loaded...
Removal and installation the sunroof fairing
Open the sliding hatch completely. Using a small screwdriver "1", squeeze the fastening clip "2" of the fairing "3". Remove the fastening clip "1" upwards from...
Open the sliding hatch completely. Using a small screwdriver "1", squeeze the fastening clip "2" of the fairing "3". Remove the fastening clip "1" upwards from...
Removal and installation the windshield
1. Windshield 2. Glue roller. Observe the minimum curing time. Consider the different distance to the edge of the glass: Dimension "a" = 30 mm±2 mm. Dimension...
1. Windshield 2. Glue roller. Observe the minimum curing time. Consider the different distance to the edge of the glass: Dimension "a" = 30 mm±2 mm. Dimension...
Removal and installation the front side glass
Instructions: Removal without damaging the glass is not provided. 1. Front side glass 2. Glue roller. Take into account the different distance of the glue...
Instructions: Removal without damaging the glass is not provided. 1. Front side glass 2. Glue roller. Take into account the different distance of the glue...
Removal the front side glass
Undamaged glass The A-pillar trim has been removed. Seal the area around the edges of the glass with fabric-backed adhesive tape "1" to protect the paintwork....
Undamaged glass The A-pillar trim has been removed. Seal the area around the edges of the glass with fabric-backed adhesive tape "1" to protect the paintwork....
Removal and installation the rear side glass
1. Rear side window. Before installation, it is necessary to lay protective film for the side window of the Audi A2 "V.A.G 1474/16" from the inside between the...
1. Rear side window. Before installation, it is necessary to lay protective film for the side window of the Audi A2 "V.A.G 1474/16" from the inside between the...
Removal and installation side glass
1. Rear window 2. Glue roller. Take into account the different distance to the edge of the glass. The distance "a" from the top of the second glue roller to...
1. Rear window 2. Glue roller. Take into account the different distance to the edge of the glass. The distance "a" from the top of the second glue roller to...
Replacing the upper moldings
Instructions. Protective moldings cannot be removed without damage. To facilitate removal, heat the moldings with a heat gun. The temperature of the surfaces...
Instructions. Protective moldings cannot be removed without damage. To facilitate removal, heat the moldings with a heat gun. The temperature of the surfaces...
Replacing lower moldings
1. Front molding. Loosen the bolts. Carefully remove the protective molding from the door. Installation: the surface to be glued must be free of glue, dust and...
1. Front molding. Loosen the bolts. Carefully remove the protective molding from the door. Installation: the surface to be glued must be free of glue, dust and...
Removal and installation the threshold trim
1. Front door 2. Front trim. Pull out to remove 3. Front molding 4. Back door 5. Rear trim. Pull out to remove 6. Rear molding
1. Front door 2. Front trim. Pull out to remove 3. Front molding 4. Back door 5. Rear trim. Pull out to remove 6. Rear molding
Removal and installation the B-pillar trim
1. Threaded bushing (4 pcs.) 2. Retainer 3/4. Combination bolt, 1.5 Nm 5. Lid 6. Threaded bushing (2 pcs.) 7. B-pillar trim. Remove the cover. Remove the cover...
1. Threaded bushing (4 pcs.) 2. Retainer 3/4. Combination bolt, 1.5 Nm 5. Lid 6. Threaded bushing (2 pcs.) 7. B-pillar trim. Remove the cover. Remove the cover...
Removal and installation the threshold trim
1. Threshold trim. Remove the front and rear threshold trim covers. Unscrew the front mudguard liner bolts. Unscrew the bolts and rear mudguard liner bolts....
1. Threshold trim. Remove the front and rear threshold trim covers. Unscrew the front mudguard liner bolts. Unscrew the bolts and rear mudguard liner bolts....
Threshold trim cover
Press the threshold trim "3" down at the "arrow" and thus release the cover clamps. Step by step remove the cover "1" from the threshold trim "3", first from...
Press the threshold trim "3" down at the "arrow" and thus release the cover clamps. Step by step remove the cover "1" from the threshold trim "3", first from...
Trunk lid trim
The number plate is removed. Remove the boot lid trim. Disconnect the plug connectors of the microswitches or the number plate light. Use a short screwdriver...
The number plate is removed. Remove the boot lid trim. Disconnect the plug connectors of the microswitches or the number plate light. Use a short screwdriver...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections of other Audi car models:
Body: Doors, locks and windows Audi 100 C3 (1982-1990, petrol)
Body: Doors, covers and windows Audi A3 Type 8L (1996-2003)
Body: Doors, locks and windows Audi A4 B8 (2007-2015)
Body: Doors, locks and windows Audi A6 C5 Allroad (1999-2005)
Body: Doors, locks and windows Audi Q5 Type 8R (2008-2017)
Body: Doors, locks and windows Audi 100 C3 (1982-1990, petrol)
Body: Doors, covers and windows Audi A3 Type 8L (1996-2003)
Body: Doors, locks and windows Audi A4 B8 (2007-2015)
Body: Doors, locks and windows Audi A6 C5 Allroad (1999-2005)
Body: Doors, locks and windows Audi Q5 Type 8R (2008-2017)
Share information:
- General information
- Introduction to the guide
- Maintenance
- Engine 1.4 l (gasoline)
- Engine repair
- Lubrication system
- Cooling system
- Exhaust system
- Engine 1.6 l (gasoline)
- Engine repair
- Lubrication system
- Cooling system
- Exhaust system
- Engine 1.2 l (diesel)
- Engine repair
- Lubrication system
- Cooling system
- Injection and turbocharging
- Engine 1.4 l (diesel)
- Engine repair
- Lubrication system
- Cooling system
- Turbocharging system
- Supply system
- Fuel injection system
- Exhaust system
- Transmission
- Mechanical gearbox 02J
- Mechanical gearbox 02T
- Mechanical gearbox 085 DS
- Chassis
- Car suspension
- Steering
- Brake system
- Body
- Exterior
- Interior
- Seats
- Doors, locks and windows
- Safety system
- Heating and air conditioning
- Electrical equipment
- Power devices
- Equipment and devices
- Wipers and washers
- Lighting and lamps
- Breakers and switches
- Electrical circuits