Car steering repair Audi Q5 (8R)

Steering wheel airbag
Steering wheel airbag 1. Airbag coil spring and return ring with slip ring "F138"; 2. Steering wheel; 3. Bolt. 30 Nm + 90°. Replace each time when removing;...

Removal the Airbag in the Steering Wheel
Note. Applies to vehicles with dynamic steering: Before removing the steering wheel from the steering column, use the steering wheel calibration device "VAS...

Steering column
Steering column 1. Bolt; 2. Support bracket; 3. Central pipe; 4. Bolt. 5 Nm; 5. Used ELV "J764". After replacing the ELV "J764" control unit, it is necessary...

Removal the steering column
Attention! Before removing the steering column, do the following: Draw a diagram of the following elements: wiring harnesses; fastening of bundles of electric...

Removal the ELV-J764 control unit-
To replace the ELV "J764" control unit, simply remove the following parts from the steering column: driver's airbag; steering wheel; steering column trim;...

Removal the Active Steering System Safety Lock
Note: When the locking magnet is removed, do not turn the steering wheel or change the straight-ahead position or the steering angle of the front wheels....

Electromechanical steering mechanism
Removal The steering rack is installed and removed together with the steering rod. Remove the front wheels. Unscrew the nut "1" of the pin of the end of the...

Electromechanical steering gear — disassembly and assembly
Electromechanical steering mechanism 1. Clamp. Replace each time it is removed. Use the clamping pliers "VAG 1682 A" to tighten the clamping clamp. Opening and...

Removal the tie rod end
Remove the front wheel. Measure and record the dimension "a" between the end of the tie rod "1" and the tie rod "2" on the left and right. The dimension "a"...

Removal the tie rod
The tie rods can be removed and installed without dismantling the steering. Remove the front wheel. Remove the sound insulation. Measure and record the...

Hydraulic steering gear
The steering rack is installed and removed together with the steering rod. I 1. Subframe; 2. Crosspiece of stretchers; 3. Intermediate steering shaft; 4. Bolt....

Removal the hydraulic power steering
Place the car on a lift. Clamp the suction hose "1" and the return hose "2" with hose clamps up to 25 mm "3094". Do not attach hose clamps up to 025 mm "3094"...

Repair of hydraulic power steering
Note: Replace the self-locking nuts and screws. Welding and straightening work on parts of the steering gear is not allowed. Use only steering gear grease to...

Removal the Servotronic solenoid valve «N119»
Replacement is only possible with the steering mechanism removed. Remove the steering mechanism. Thoroughly clean the steering mechanism "6" in the area of the...

Adjusting the hydraulic power steering
A second mechanic is required for adjustment. Adjustment is performed with the engine off. Remove sound insulation. Set the power steering mechanism to the...

Removal and installation the tie rod end
Two different tie rod end housings were installed in series, they differ in the length of the thread on the joint pin. When replacing the tie rod end, ensure...

Removal the tie rods
The tie rods can be removed and installed without dismantling the steering. Place the car on a lift. Remove the wheel. Remove the sound insulation. Measure and...

Removal the corrugated cover
If the boot is damaged, moisture and dirt will get into the steering gear. There should be a tangible film of grease on the rack teeth. If there is no...

Checking the power steering fluid level
Do not start the engine and set the front wheels straight ahead. Oil when cold (approx. 20°C): Unscrew the cap. Wipe the dipstick with a clean cloth. Screw the...

Bleeding the steering after reinstallation
After performing work on reinstalling the steering system, it is necessary to bleed air from the steering system in different ways depending on the scope of...

Checking the tightness of the steering system
It is necessary to check the tightness of the steering control after installation work and in the absence of hydraulic fluid in the expansion tank. Remove the...

Vane pump, hydraulic lines, expansion tank, 4-cylinder diesel engine
Repair work for the vane pump is not provided. In case of complaints, the cause should be determined by pressure testing and leak testing. If a fault is found,...

Vane pump, hydraulic lines, expansion tank, vehicle with 4-cylinder TFSI engine
Note: Repair work on the vane pump is not provided. In case of complaints, the cause must be determined by pressure testing and leak testing. If a fault is...

Vane pump, hydraulic lines, expansion tank, 6-cylinder diesel engine vehicle
Note. Repair work for the vane pump is not provided. In case of complaints, the cause must be determined by pressure testing and leak testing. If a fault is...

Vane pump, hydraulic lines, expansion tank, vehicles with 6-cylinder FSI engine
Note. Repair work for the vane pump is not provided. In case of complaints, the cause must be determined by pressure testing and leak testing. If a fault is...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Share information:

Q7 4L(2005-2015, diesel)

Q5 8R(2008-2017)