Manual gearbox 0B1 and clutch of car Audi Q5 (8R)
Marking of the KP
Location at the checkpoint "Arrow A". MCP 0V1 "Strelka V". Letter designation and date of manufacture "Strelka S". Letter designation and production date under...
Location at the checkpoint "Arrow A". MCP 0V1 "Strelka V". Letter designation and date of manufacture "Strelka S". Letter designation and production date under...
Parts and components of the pedal assembly
Note: Lubricate all bearing and contact surfaces with grease G 000 450 02-. Make sure that no brake fluid gets into the footwell, on the radiator reservoir or...
Note: Lubricate all bearing and contact surfaces with grease G 000 450 02-. Make sure that no brake fluid gets into the footwell, on the radiator reservoir or...
Removal the servo spring
Remove the front panel trim on the driver's side. Remove the left footwell air duct. Lightly press the clutch pedal "1" in the "direction of the arrow". At the...
Remove the front panel trim on the driver's side. Remove the left footwell air duct. Lightly press the clutch pedal "1" in the "direction of the arrow". At the...
Removal the clutch pedal
Remove the support bracket. Remove the servo spring "2". Remove the locking pin "1". Remove the bearing shaft "2", for which lift the locking tongue "arrow A"...
Remove the support bracket. Remove the servo spring "2". Remove the locking pin "1". Remove the bearing shaft "2", for which lift the locking tongue "arrow A"...
Hydraulic clutch system
Take into account the instructions for removing and installing the clutch master and slave cylinder. Hydraulic clutch system 1. Clutch slave cylinder: Do not...
Take into account the instructions for removing and installing the clutch master and slave cylinder. Hydraulic clutch system 1. Clutch slave cylinder: Do not...
Instructions for removing and installing the clutch master and slave cylinder
If it is necessary to replace the clutch master/slave cylinder due to a suspected malfunction, first check its functionality. If the slave cylinder is removed...
If it is necessary to replace the clutch master/slave cylinder due to a suspected malfunction, first check its functionality. If the slave cylinder is removed...
Checking the operation of the master and slave clutch cylinders
Before replacing the master/slave cylinder in the event of the following faults, first perform the corresponding checks.
Before replacing the master/slave cylinder in the event of the following faults, first perform the corresponding checks.
Clutch engagement noises
First check the spring assembly or clutch pedal sensor for noise. If there is noise, remove the spring assembly and repeat the check. Replace the corresponding...
First check the spring assembly or clutch pedal sensor for noise. If there is noise, remove the spring assembly and repeat the check. Replace the corresponding...
Removal the clutch master cylinder
Observe the instructions for removing and installing the master and slave cylinders of the clutch. Disconnect the battery. Remove the switching unit. When...
Observe the instructions for removing and installing the master and slave cylinders of the clutch. Disconnect the battery. Remove the switching unit. When...
Replacing the clutch slave cylinder
Observe the instructions for removing and installing the clutch master and slave cylinders. If present, remove the rear noise insulation screen "2". To remove...
Observe the instructions for removing and installing the clutch master and slave cylinders. If present, remove the rear noise insulation screen "2". To remove...
Clutch module
Clutch module A. Locking pin: not available on all vehicles; when connecting the clutch module "2" to the driven disk "1" the locking pin "A" (if available)...
Clutch module A. Locking pin: not available on all vehicles; when connecting the clutch module "2" to the driven disk "1" the locking pin "A" (if available)...
Gear shift mechanism
Gear shift mechanism "Arrow A". Switching stroke; "Arrow B". Movement of choice; 1. Connecting rod; 2. Push rod; 3. Shift rod; 4. Gear shift lever Handle with...
Gear shift mechanism "Arrow A". Switching stroke; "Arrow B". Movement of choice; 1. Connecting rod; 2. Push rod; 3. Shift rod; 4. Gear shift lever Handle with...
Removal the gear shift mechanism
Turn off the ignition. Remove the gearshift knob with the gearshift lever sleeve. Remove the climate control and indicator unit. Remove the control panel of...
Turn off the ignition. Remove the gearshift knob with the gearshift lever sleeve. Remove the climate control and indicator unit. Remove the control panel of...
Adjusting the gear shift mechanism
The initial conditions for correct adjustment of the gearshift drive are the following: faultless drive and transmission parts of the gearshift mechanism, easy...
The initial conditions for correct adjustment of the gearshift drive are the following: faultless drive and transmission parts of the gearshift mechanism, easy...
Checking the gearshift lever adjustment
Start the engine. Press the clutch pedal. Shift through all gears several times. Engage the reverse gear lock (move the gearshift lever down) and set the...
Start the engine. Press the clutch pedal. Shift through all gears several times. Engage the reverse gear lock (move the gearshift lever down) and set the...
Gearbox removal — vehicles with 4-cylinder diesel engine
Set the front wheels to the straight-ahead position. Turn off the ignition. Disconnect the battery. Carefully remove the engine compartment cover "in the...
Set the front wheels to the straight-ahead position. Turn off the ignition. Disconnect the battery. Carefully remove the engine compartment cover "in the...
Checking the transmission oil level in the manual transmission
Remove rear noise insulation "2". Unscrew the threaded plug of the oil filler hole "arrow" to check the gearbox oil level. Specified value: The oil level is...
Remove rear noise insulation "2". Unscrew the threaded plug of the oil filler hole "arrow" to check the gearbox oil level. Specified value: The oil level is...
Removal the gear position sensor «F208» with the gearbox installed
Remove the rear noise insulation "2". Disconnect the exhaust system by loosening the clamp "arrows". Tie the exhaust inlet pipe on the side with wire to the...
Remove the rear noise insulation "2". Disconnect the exhaust system by loosening the clamp "arrows". Tie the exhaust inlet pipe on the side with wire to the...
Removal the neutral position sensor of the gearbox «G701»
Only for cars with start-stop system. Remove rear noise insulation "2". Select 4th gear, for this point gearshift lever "2" forward "direction of arrow"....
Only for cars with start-stop system. Remove rear noise insulation "2". Select 4th gear, for this point gearshift lever "2" forward "direction of arrow"....
Crankcase seals
The "C" and "D" lip seals can be replaced with the gearbox installed. Crankcase seals A. Primary shaft lip seal; B. Left shaft lip seal with flange; C. Right...
The "C" and "D" lip seals can be replaced with the gearbox installed. Crankcase seals A. Primary shaft lip seal; B. Left shaft lip seal with flange; C. Right...
Removal the differential
The differential can also be removed and installed without dismantling the gearshift mechanism, primary shaft, secondary shaft, axle shaft/drive pinion and...
The differential can also be removed and installed without dismantling the gearshift mechanism, primary shaft, secondary shaft, axle shaft/drive pinion and...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Share information:
- General information
- Operating instructions
- Maintenance
- Power unit
- Diesels 3.0 l (BUG, BUN, CAS)
- Diesels 3.0 l (CATA, CCMA)
- Diesels 3.0 l (CJGA/CJGC)
- Diesels 4.2 l (BTR, CCFA/CCFC)
- Cooling system
- Fuel and exhaust system
- Engine management system
- Starting and charging
- Transmission
- Automatic gearbox
- Drive shafts
- Chassis
- Brake system
- Front suspension
- Rear suspension
- Steering system
- Body
- Air conditioner
- Exterior
- Interior
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- User manual
- Power unit
- Petrol engine 2.0 l
- Petrol engine 3.2 l
- Fuel system (petrol)
- Diesel 2.0 liter (CA)
- Diesel 2.0 liter (CG/CJ/CM)
- Diesel engine 3.0 l
- Fuel system (diesel)
- Transmission
- Manual gearbox 0B1
- Manual gearbox 0B2
- Automatic gearbox 0B5
- Automatic gearbox 0B6
- Chassis
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body
- Exterior
- Interior
- Doors, locks and windows
- Safety system
- Ventilation and heating
- Electrical equipment
- Power devices
- Equipment and devices
- Lighting and alarm
- Audio system
- Electrical circuits