Table of contents: Keys and control lamps of the… ↓ Turning the independent… ↓ Turning the independent… ↓
Keys and control lamps of the independent heater remote control
"A". Power button.
"B". Power button.
"C". Counter, lamp (flashes red or green).
Instructions: In order for the remote control to recognize key presses and transmit a radio signal, the corresponding key must be held down for approx. 3 seconds. If the remote control's power sources are so discharged that transmitting a radio signal of sufficient strength is impossible, the "C" indicator lamp will not light when pressing the "A" on/off "B" button. When the power button "A" is pressed, the control lamp "C" lights up green for a short time (approx. 2 sec) to indicate that the operation check is in progress. If the signal to turn on the used auxiliary heater "J364" is received correctly and there is no malfunction in the independent heater, the used auxiliary heater "J364" transmits a feedback signal, and then the control lamp "C" flashes 30 times with a frequency of 1 Hz (1 pulse per second) green light (feedback signal confirming the normal operation of the system.). If the signal for turning on the used additional heater "J364" is not received correctly, for example, due to the distance to the vehicle being too great (unable to contact the used vehicle) the control lamp "C" flashes red 30 times. If there is a malfunction in the car or independent heater (e.g., turning on the independent heater is impossible due to lack of fuel in the fuel. tank) used additional heater "J364" transmits a malfunction message, and the control lamp "C" flashes red 30 times. The control lamp "C" lights up red for a short time (about 2 sec) after pressing the power button "B" to check the operation, and then the control lamp "C" flashes 30 times at a frequency of 1 Hz (1 pulse per second) red light. If the signal to turn off the used auxiliary heater "J364" is not received correctly, for example due to the distance to the vehicle being too great (contact with the used one is impossible) after pressing the key, the "C" control lamp flashes 10 times at a frequency of 4 Hz (4 pulses per second) red light. When sending a radio signal, hold the remote control with the antenna facing up. Make sure to maintain a sufficiently large distance to the car antenna when pressing the remote control buttons. If the radio signal is strong, problems with entry may occur. If necessary, cover the transmitting antenna with your hand or maintain a minimum distance of 10 m from the vehicle. The radio receiver of the "R64" auxiliary heater can be switched to the energy saving mode of the used "J364" auxiliary heater (the radio signal can no longer be received, and the quiescent current consumption decreases from approximately 1 mA to 0.04 mA). Depending on the selected operating mode (autonomous heater or autonomous ventilation) certain error messages. having a negative impact on the operation of the autonomous heater/autonomous ventilation. are not stored in the memory of the used auxiliary heater "J364". Therefore, if there are complaints about the independent heater, also consider the fault memory. pan. controls and display used Climatronic "J255".
Turning the independent heater/ventilation system on and off. via MMI
Conditions: Autonomous heater adapts to used and indicator, used Climatronic "J255" (check and perform coding). For the auxiliary heater to be activated by the used J364 auxiliary heater or for the auxiliary heater activation function to be activated, there must be sufficient fuel in the fuel tank. When the ignition is on, the fuel level indicator "A" should not be in the red zone. The used additional heater "J364" should not have any fault codes. The vehicle's battery "A" must be sufficiently charged. Presence of faults. vehicle data buses are not allowed. Transport mode and protection of autonomous heater components must be inactive.
Turning the independent heater/ventilation on and off
Press the "A" key on the remote control to turn it on or the "B" key (oFF key) to turn off the independent heater/ventilator. Or: Turn on the ignition. Press the CAR button on the MMI keyboard. Press the Climate button to send control signals. Select Autonomous Heating or Autonomous Ventilation using the rotary push wheel and make the required settings.
Setting up an independent heater/autonomous ventilation
Turn on the ignition. Press the CAR button on the MMI keyboard. Press the Climate button to send control signals. Select Autonomous Heating or Autonomous Ventilation using the rotary push wheel and make the required settings. Select on pan. control and indication of the used Climatronic "J255" required temperature.
The original text of the material can be found on the website AudiManual