Table of contents: Radiator frame with attachments ↓ Removal the lock bracket cover ↓ Radiator frame stretcher ↓ Removal and installation the water… ↓ Removal additional trim ↓ Front wall of the water drainage box ↓
Radiator frame with attachments
1. Bolt: 30 Nm; 3 pcs on each side.
2. Safety bar: fixed with bolt "3" on the radiator frame; when dismantling the radiator frame, it is not necessary to remove it from the brackets.
3. Bolt: 4 Nm; serves to fix the safety bar. on the radiator frame.
4. Radiator frame. Removal: remove the lock bracket cover, remove the front bumper, disconnect all electrical connections. wires and hoses going to the radiator frame from the connection points, disconnect the cable rod of the hood lock on the coupling, unscrew the bolts "5", unscrew the bolts "1" from the side member (3 pieces on each side). Safety beams. with brackets, each secured with one bolt "1" on the radiator frame and should not be removed. Unscrew the bolts "6" from the bottom of the radiator frame, remove the radiator frame with the headlights in the forward direction.
Installation: in reverse order, after installation the headlights must be adjusted.
5. Bolt: 10 Nm.
6. Bolt: 1.5 Nm.
7. Wing.
Removal the lock bracket cover
1. Trim: to remove, unscrew the locking pin, this will unlock the clamp, remove the clamp from the trim, remove the trim from the radiator grille in the rear direction: when installing, the projections of the trim must be fixed in the radiator grille and on the side of the bumper trim, install the clamp through the trim into the radiator frame and press in the locking pin.
2. Expansion piston: when removing, unscrew the clamping pin; when installing, press the clamping pin; 4x.
3. Radiator frame.
4. Radiator grille.
Radiator frame stretcher
1. Bolt: 1.5 Nm.
2. Stretch for radiator frame, left: secured with nut "6" on the radiator frame.
3. Radiator frame.
4. Bracket: insert into the radiator frame from below.
5. Frame of mounted units.
6. Nut: 23 Nm.
Removal and installation the water drainage box lining
1. Additional trim, right: when removing, first remove the front mounting clip; lift the trim from the front and remove it from the cover of the water drainage box.
2. Cover of the water drainage box: wiper arms removed: additional trim (left, center and right) removed; disconnect clamps "3", remove the trim, starting from the edge of the glass, from the mounting frame vertically upwards. To facilitate removal/installation, spray a small amount of industrial soap solution onto the windshield mounting frame.
3. Clamp: After installing the water drain box cover, push the clamps to the indicated places.
4. Windshield.
Removal additional trim
1. Additional trim, central: first unlock from below, then loosen the clamps "2" at the back (squeeze slightly from below) and remove it from the cover of the water drainage box in an upward direction.
2. Latch: When removing, press lightly from below and pull out.
3. Additional trim, left: first unlock from below, then loosen the fasteners at the back and pull it out of the water drainage box cover in an upward direction.
4. Sheathing of the water drainage box.
5. Water drainage box cover fasteners.
Front wall of the water drainage box
1. Bolt: 7 Nm.
2. Clamping washer: When installing, press on the threaded pin of the front wall of the water drainage box.
3. Sound insulation: the sound insulation is fixed with a clamping washer on the front wall of the water drainage box.
4. Nut: 7 Nm.
5. Front wall of the water drain box: before removal: remove the brace, unscrew the windshield washer reservoir from the connection going to the front wall of the water drain box, remove the vacuum line going to the brake booster. drive, unblock the vacuum line in the front wall of the water drain box; to remove, unscrew bolts "1" and nut "4".
6. Gasket: slide the gasket from below.
7. Water drainage box.
8. Edge protection: Install the edge protection on the tongue on the front wall of the water drainage box.
Text provided by the online resource: Audimanual.ru