Onboard Electrical Specifications Warning: Individual characteristics are also given in the text of the Chapter and, if mandatory, are highlighted in bold Incandescent lamps 12 V To be able to...
Electrical comfort system The electrical equipment of the car's comfort system refers to a combination of various devices, such as a single lock, remote control, exterior mirror...
Checking the wiper motor The wiper motor is located in the water collection area under the windshield. To check it is necessary to remove the corresponding cover. Terminal designation...
Checking the heated rear window When the heated rear window is turned on, the field with visible lines of wires should be free of coating or snow after a while. Order of execution 1. If there...
Stoplight test Order of execution 1. If the brake light does not come on, check the fuse in the fuse box first. 2. If the fuse is OK, check the bulb and replace if necessary....
Removal, installation and check of a sound signal Behind the front bumper on the left side, one high and one low tone sound signal is installed. A relay is installed between the power button and the signal to...
Circuit breakers The electrical circuits of the vehicle are protected by a combination of fuses, circuit breakers and fuse links. A blown fuse is easy to distinguish from a...
Fusible links — general information Protection of some circuits is carried out by including fusible links in their electrical circuit. Inserts are usually used to protect non-fused circuits such...
Circuit breakers (thermal relays) Thermal relays are used to protect components such as electric windows, door locks and headlight adjustment. Some of the circuit breakers are housed in a fuse...
Relay — general information Relays are used to supply electrical current to components in some of the vehicle's electrical accessories. Failure of the relay to function properly leads to...
Replacing the Remote Control Key Batteries Withdrawal Warning: When removing batteries, check that the polarity is marked on the batteries. If polarity is not indicated, mark the position of the...
Replacing the battery/light key lamp Withdrawal Warning: When removing batteries, check that the polarity is marked on the battery. If polarity is not indicated, mark the position of the battery....
Anti-theft lock Anti-theft lock elements 1 - control device for the electronic anti-theft locking system Built into the instrument cluster 2 - anti-theft blocking reading coil...
Replacing outdoor lamps 1. Turn off the corresponding lamp switch. 2. Switch off the ignition. Near and far light Warning: H7 bulbs are pressurized and may crack if replaced....
Replacing interior light bulbs Indoor/reading light 1. Carefully remove the diffuser of the three-part lamp with your fingers from the front. 2. Remove the defective soffit from the...
Removal and installation of a headlight Headlamp with beam adjustment mechanism 1 - clamps (6 pcs.) 2 - diffuser 3 - diffuser seal 4 - headlight housing 5 - low beam lamp 6 - connector 7 - electric...
Removal and installation of a back lantern Withdrawal 1. Remove the lamp holder -1-, refer to subsection Replacing outdoor lamps . 2. Loosen 4 fastening nuts (arrows). 3. Squeeze the stopper -4- and...
Headlight adjustment Headlight adjustment screws (left main headlight shown, right headlight adjusting screws mirrored) 1 - vertical adjustment 2 - horizontal adjustment Order of...
Devices — general information The instruments are on the dashboard. The dashboard must be removed if necessary, for example, to replace the lamp. If other devices are faulty, it is...
Removal and installation of the dashboard Connectors on the back of the dashboard A - connector 32 pins, blue B - connector 32 pins, green C - connector 20 pins, red. Execution only «Higline» 1 - high...
Removal and installation of the steering column switch The stalk includes: both turn signal/high beam and wiper switches. Withdrawal 1. Disconnect the negative cable (–) battery with the ignition off. Warning: As a...
Removal and installation of switches and lamps Switch/dimmer 1. Press the light switch -1- and at the same time turn it to the left -2-. 2. Hold the switch in this position and remove the light switch...
Removal, installation and coding of the radio receiver Location of elements and wiring of radio equipment 1 - radio receiver 2 - low frequency loudspeaker, 2 - Ohm/20W 3 - mid/high frequency loudspeaker, 2 ohm/20 W...
Entering the radio code (Valid only for coded radios) A sign of a coded radio is the presence of a red symbol in the form of a key on the front trim. If the red LED on the front side...
Removing and installing the loudspeaker Low–/medium–/high-frequency loudspeaker 1. Remove the door trim, refer to subsection Removal and installation of facing of a door . 2. Carefully detach the...
Removal and installation of the roof antenna Roof antenna 1 - antenna 2 - antenna base cover 3 - antenna wire connector 4 - connector (radio) 5 - radio/telephone antenna base 6 - nut 7 - antenna base seal...
Removal and installation of a cleaner of back glass Rear window cleaner 1 - cover 2 - nut, 15 Nm 3 - lever 4 - seal 5 - jet 6 - sealing ring 7 - electric motor 8 - nut, 8 Nm 9 - rubber ring 10 - remote element...