Table of contents: Rear light assembly, outer part ↓ Removal and installation of rear.… ↓ Removal and installation the lamp… ↓ Replacing the rear side marker light… ↓ Inner rear light ↓ Removal and installation the rear… ↓ Removal and installation the lamp… ↓
Rear light assembly, outer part
1. Rear light bulb. running: left rear light lamp. "M16" travel, right rear light bulb. "M17" course; 12 V, 16 Bt; W16W.
2. Lamp: 12V, 21W.
3. Turn signal lamp: rear lamp. left turn signal "M6". rear lamp. right turn signal "M8"; 12 V, 21 W.
4. Lamp holder.
5. Nut: 3.5 Nm.
6. Threaded pin: 3.5 Nm.
7. External rear lights, LED replacement is not possible, outer part of the rear. the headlight assembly must be replaced completely.
Removal and installation of rear. side light
Turn off the ignition. Set the light switch to position 0. Open the trunk side trim cover. Unscrew the threaded pin "2". Tilt the rear. block of lights "1" outward "arrow" and at the same time remove the lock bolt from the body. Disconnect the plug connection.
Installation in reverse order. Self-adhesive seal on the rear body. the clearance light should seal well. Install the rear. the light assembly on the body and press the locking bolt into the hole. Tighten the pin with thread "2".
Removal and installation the lamp holder
Remove the outer rear parking light. Unscrew the "arrow" nuts. Remove the bulb socket "2" from the rear light assembly "1". Unscrew the bulbs from the socket. Unscrew the turn signal lamp "3". Remove the lamp "4" of the rear parking light/brake light and the lamp "5" of the rear light. move.
Installation in reverse order. Insert new lamps into the socket, being careful not to touch the glass bulb of the lamp with bare hands. Install the rear. external clearance light.
Replacing the rear side marker light bulb "M37"/"M38"
The rear side marker light bulb is an LED and is installed in the outer part of the rear. block of lights. Replacing LEDs is not possible, the outer part of the rear. the headlight assembly must be replaced completely.
Inner rear light
1. Inner rear light.
2. Rear fog light bulb: left rear fog light bulb. fog light "L46", right rear lamp. fog light "L47"; 12 V, 21 W.
3. Tail light bulb: left rear light bulb. side light "M4". right rear lamp. side light "M2"; 12 V, 21 W.
4. Lamp holder.
5. Tail light bulb: left rear light bulb. side light 2 "M49", right rear lamp. side light 2 "M50"; 12 V, 21 W.
6. Nut: 3.5 Nm.
7. Clamp bracket: for mounting the rear light. lighting to the trunk door.
Removal and installation the rear interior marker light
Turn off the ignition. Set the light switch to position 0. Remove cover "1" from the outside of the driver, "arrow".
Disconnect plug connection "2". Unscrew nut "3" and remove clamp bracket "4". Slightly move the inner part of the rear. the light unit outwards "arrow A" and remove "in the direction of arrow B" from the trunk.
Installation
Installation in reverse order. Ensure that the gasket between the body and the rear housing is installed correctly. light. Install the inner section of the rear. lamp on the outer edge of the trunk door. Slide the clamping bracket "2" onto the threaded pin of the inner part of the rear. block of lights. The guide pin "4" of the rear light must enter the fastening "3" of the clamp bracket. Tighten nut "1". When tightening the nuts, the clamp bracket is wedged backwards. "arrow" cover.
Removal and installation the lamp holder
Turn off the ignition. Set the light switch to position 0. Remove cover "1" from the outside of the driver, "arrow". Remove lamp socket "2" from the housing by pressing the locking clip "1" in the direction of the arrow. Unscrew the bulbs from the socket. Remove lamps "4" and "5" of the parking light. Unscrew the fog light bulb "3".
Installation in reverse order: insert new lamps into the socket, being careful not to touch the glass bulb of the lamp with bare hands.
(The original version of the article is posted on the website: AudiManual)