Car V8 Gasoline Engines Audi A6 C5 Allroad
General information about V8 petrol engines
Specifications Engine designation BAS Working volume, cm³ 4163 Power, kW at rpm 221/6200 Power, hp at rpm 300/6200 Maximum torque, Nm at rpm 380/2600-4700...
Specifications Engine designation BAS Working volume, cm³ 4163 Power, kW at rpm 221/6200 Power, hp at rpm 300/6200 Maximum torque, Nm at rpm 380/2600-4700...
Gas distribution mechanism drive chain-design description
The timing mechanism is driven by several chains. The main chain drives the exhaust camshafts from the drive sprocket on the crankshaft (see illustration 2.0)....
The timing mechanism is driven by several chains. The main chain drives the exhaust camshafts from the drive sprocket on the crankshaft (see illustration 2.0)....
Timing chain — removal and installation
Removal 1. Remove the camshaft drive chains (see the relevant chapter). 2. Remove the accessory drive chain (see the relevant chapter). 3. Unscrew the...
Removal 1. Remove the camshaft drive chains (see the relevant chapter). 2. Remove the accessory drive chain (see the relevant chapter). 3. Unscrew the...
Camshaft Drive Chains — Removal and Installation
Removal 1. Remove the engine and mount it on a suitable support or mounting stand (see the relevant chapter). 2. Disconnect plug 1 from the throttle valve, and...
Removal 1. Remove the engine and mount it on a suitable support or mounting stand (see the relevant chapter). 2. Disconnect plug 1 from the throttle valve, and...
Auxiliary Unit Drive — Design Description
The oil and water pumps are driven by a separate chain from the sprocket on the crankshaft (see illustration 4.0). 4.0. Auxiliary units drive: 1 - timing chain...
The oil and water pumps are driven by a separate chain from the sprocket on the crankshaft (see illustration 4.0). 4.0. Auxiliary units drive: 1 - timing chain...
Accessory Drive Chain — Removal and Installation
Removal 1. Drain the engine oil. 2. Remove the engine and mount it on a suitable support or mounting stand (see the relevant chapter). 3. Lock the drive disk...
Removal 1. Drain the engine oil. 2. Remove the engine and mount it on a suitable support or mounting stand (see the relevant chapter). 3. Lock the drive disk...
Generator Drive — Design Description
5.0. Generator Drive: 1 - bolt. Tightening torque - 22 Nm 2 - bolt. Tightening torque - 22 Nm 3 - generator drive V-belt tensioner 4 - generator mounting bolt....
5.0. Generator Drive: 1 - bolt. Tightening torque - 22 Nm 2 - bolt. Tightening torque - 22 Nm 3 - generator drive V-belt tensioner 4 - generator mounting bolt....
V-ribbed alternator drive belt — removal and installation
Removal Caution! When removing the V-belt of the alternator drive, it will be necessary to install the upper front crossmember (see illustration 5.0a) into the...
Removal Caution! When removing the V-belt of the alternator drive, it will be necessary to install the upper front crossmember (see illustration 5.0a) into the...
Valve mechanism and valve — design description
6.0. Valve mechanism: I - camshaft position adjuster mounting bolt. Tightening torque: 1st pass - 5 Nm; 2nd pass - turn 90° 2 - camshaft position regulator 3 -...
6.0. Valve mechanism: I - camshaft position adjuster mounting bolt. Tightening torque: 1st pass - 5 Nm; 2nd pass - turn 90° 2 - camshaft position regulator 3 -...
Camshafts — Removal and Installation
Removal 1. Remove the engine and mount it on a suitable support or mounting stand (see the relevant chapter). 2. Remove the camshaft drive chains (see the...
Removal 1. Remove the engine and mount it on a suitable support or mounting stand (see the relevant chapter). 2. Remove the camshaft drive chains (see the...
Cylinder head — design description
7.0. Cylinder head. The illustration shows the right cylinder head: 1 - cylinder head gasket 2 - engine lifting eye 3 - eye mounting bolt. Tightening torque -...
7.0. Cylinder head. The illustration shows the right cylinder head: 1 - cylinder head gasket 2 - engine lifting eye 3 - eye mounting bolt. Tightening torque -...
Cylinder head — removal and installation
Removal Attention! The cylinder head is removed with the engine removed. 1. Remove the engine and mount it on a suitable support or mounting stand (see the...
Removal Attention! The cylinder head is removed with the engine removed. 1. Remove the engine and mount it on a suitable support or mounting stand (see the...
Engine — removal and installation
Removal 1. Set the gear shift lever to neutral position. 2. Remove the seal from the fairing (see arrows in the illustration), and then remove the grille 1 of...
Removal 1. Set the gear shift lever to neutral position. 2. Remove the seal from the fairing (see arrows in the illustration), and then remove the grille 1 of...
Compression in cylinders — check
Compression testing allows you to draw conclusions about the engine's condition. Based on the results of the test, you can judge whether the engine has...
Compression testing allows you to draw conclusions about the engine's condition. Based on the results of the test, you can judge whether the engine has...
Oil pump — design description
10.0. Oil pump: 1 - bolt. Tightening torque -10 Nm 2 - lower part of the oil pan 3 - oil intake pipe mounting bolt. Tightening torque - 10 Nm 4 - oil intake...
10.0. Oil pump: 1 - bolt. Tightening torque -10 Nm 2 - lower part of the oil pan 3 - oil intake pipe mounting bolt. Tightening torque - 10 Nm 4 - oil intake...
Oil pump — removal and installation
Removal 1. Remove the lower part of the oil pan (see the relevant chapter). 2. Disconnect the coolant hose from the water pump by removing clamp 1 (see...
Removal 1. Remove the lower part of the oil pan (see the relevant chapter). 2. Disconnect the coolant hose from the water pump by removing clamp 1 (see...
Oil pan — design description
11.0. Oil pan: 1 - lower part of the oil pan 2 - oil pan lower part mounting bolt. Tightening torque - 10 Nm 3 - oil line mounting bolts. Tightening torque -...
11.0. Oil pan: 1 - lower part of the oil pan 2 - oil pan lower part mounting bolt. Tightening torque - 10 Nm 3 - oil line mounting bolts. Tightening torque -...
Oil pan — removal and installation
Removal Bottom of the oil pan 1. Drain the coolant. 2. Unscrew the drain plug at the bottom of the oil pan and drain the engine oil. 3. Set the upper front...
Removal Bottom of the oil pan 1. Drain the coolant. 2. Unscrew the drain plug at the bottom of the oil pan and drain the engine oil. 3. Set the upper front...
Oil radiator — removal and installation
Removal 1. Remove the generator (see the relevant chapter). 2. Unscrew the bolts (see arrows in the illustration) and remove the generator bracket. 12.2....
Removal 1. Remove the generator (see the relevant chapter). 2. Unscrew the bolts (see arrows in the illustration) and remove the generator bracket. 12.2....
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections of other Audi car models:
Power unit: Petrol injection Audi 80 B4 (1991-1996)
Power unit: Petrol engines 1.8 l Audi A4 B8 (2007-2015)
Power unit: Petrol engine 3.7L and 4.2L Audi A8 D2 (1994-2002)
Power unit: Fuel system (petrol) Audi Q5 Type 8R (2008-2017)
Power unit: Petrol injection Audi 80 B4 (1991-1996)
Power unit: Petrol engines 1.8 l Audi A4 B8 (2007-2015)
Power unit: Petrol engine 3.7L and 4.2L Audi A8 D2 (1994-2002)
Power unit: Fuel system (petrol) Audi Q5 Type 8R (2008-2017)
Share information:
- General information
- User manual
- Maintenance
- Troubleshooting
- Power unit
- V6 petrol engines
- V8 petrol engines
- Diesel engines
- Cooling and heating system
- Injection system (gasoline)
- Fuel system (diesel)
- Supply system
- Exhaust system
- Ignition system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Chassis
- Brake system
- Car suspension
- Steering
- Body
- Body elements
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Power devices
- Electrical circuits
- Schemes (petrol engine 2.7 l)
- Schemes (petrol engine 4.2 l)
- Schemes (diesel engine 2.5 l)
- General information
- User manual
- Maintenance
- Power unit
- Engine repair
- Cooling system
- Fuel system
- Engine management
- Fuel system (diesel)
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Chassis
- Front suspension
- Rear suspension
- Steering
- Wheels and tires
- Brake system
- Body
- Exterior
- Interior
- Electrical equipment
- Air conditioner
- Equipment and devices
- Electrical circuits
- General information
- User manual
- Maintenance (gasoline)
- Maintenance (Diesel)
- Gasoline engines
- 4 cylinder engines
- 5 cylinder engines
- 6 cylinder engines
- Diesel engines
- 4 cylinder engines
- 5 cylinder engines
- Engine repair
- Removal and reassembly
- Cooling system
- Single point injection system
- Multipoint injection system
- MPI/MPFI injection system
- Fuel system (diesel)
- Exhaust system
- Ignition system
- Transmission
- Clutch
- Manual transmission
- Automatic transmission
- Drive shafts
- Chassis
- Brake system
- Front suspension
- Rear suspension
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Power devices
- Lighting and appliances
- Electrical circuits