Diesel car engines Audi A6 C5 Allroad
General information about diesel engines
Specifications Audi Allroad vehicles are equipped with V-shaped 6-cylinder diesel engines with a volume of 2.5 liters. The cylinder blocks are cast from grey...
Specifications Audi Allroad vehicles are equipped with V-shaped 6-cylinder diesel engines with a volume of 2.5 liters. The cylinder blocks are cast from grey...
Crankshaft — design description
1.0. Crankshaft: 1 - centering sleeve 2 - crankshaft gear 3 - crankshaft 4 - centering pin 5 - bar 6 - bar mounting bolt. Tightening torque - 22 Nm 7 -...
1.0. Crankshaft: 1 - centering sleeve 2 - crankshaft gear 3 - crankshaft 4 - centering pin 5 - bar 6 - bar mounting bolt. Tightening torque - 22 Nm 7 -...
Timing drive — design description
2.0. Gas distribution mechanism drive: 1 - leading gear of the gas distribution mechanism on the crankshaft 2 - timing belt tensioner 3 - tensioner mounting...
2.0. Gas distribution mechanism drive: 1 - leading gear of the gas distribution mechanism on the crankshaft 2 - timing belt tensioner 3 - tensioner mounting...
Timing Belt — Removal and Installation
Removal 1. Remove the accessory drive V-belt (see the relevant chapter). 2. Remove the cap from the oil filler neck. 3. Turn the crankshaft in the direction of...
Removal 1. Remove the accessory drive V-belt (see the relevant chapter). 2. Remove the cap from the oil filler neck. 3. Turn the crankshaft in the direction of...
Auxiliary Unit Drive — Design Description
3.0. Auxiliary units drive: 1 - V-belt for auxiliary drive 2 - generator mounting bushing 3 - lower generator mounting bolt. Tightening torque - 22 Nm 4 -...
3.0. Auxiliary units drive: 1 - V-belt for auxiliary drive 2 - generator mounting bushing 3 - lower generator mounting bolt. Tightening torque - 22 Nm 4 -...
V-ribbed auxiliary drive belt — removal and installation
Depending on the vehicle's configuration, the V-belt can drive various auxiliary units, such as the generator, power steering pump, radiator fan and, if...
Depending on the vehicle's configuration, the V-belt can drive various auxiliary units, such as the generator, power steering pump, radiator fan and, if...
Cylinder head — design description
4.0. Cylinder head: 1 - cylinder head 2 - cylinder head cover gasket 3 - cylinder head mounting bolt. Bolts must be replaced after each dismantling 4 -...
4.0. Cylinder head: 1 - cylinder head 2 - cylinder head cover gasket 3 - cylinder head mounting bolt. Bolts must be replaced after each dismantling 4 -...
Cylinder head — removal and installation
Attention! Modification of the cylinder head is not permitted. Attention! When dismantling the vacuum pump, it should be turned in the direction of the arrow,...
Attention! Modification of the cylinder head is not permitted. Attention! When dismantling the vacuum pump, it should be turned in the direction of the arrow,...
Valve mechanism and valve — design description
5.0. Valve mechanism. Cars with AFB, AKE, AKN, AYM, BFC engines: 1 - Front camshaft bearing cover 2 - deaf (cap) camshaft bearing front cover fastening nut....
5.0. Valve mechanism. Cars with AFB, AKE, AKN, AYM, BFC engines: 1 - Front camshaft bearing cover 2 - deaf (cap) camshaft bearing front cover fastening nut....
Camshafts — Removal and Installation
Removal 1. Cars with parking heater. Unscrew the bolts (see arrows in the illustration) fastening the heater pipe to the soundproofing shield. 5.1. Unscrew the...
Removal 1. Cars with parking heater. Unscrew the bolts (see arrows in the illustration) fastening the heater pipe to the soundproofing shield. 5.1. Unscrew the...
Engine piston and connecting rod — design description
6.0. Engine piston and connecting rod: 1 - connecting rod cap mounting bolts. Tightening torque: 1st pass - 30 Nm; 2nd pass - turn 90° 2 - connecting rod cap....
6.0. Engine piston and connecting rod: 1 - connecting rod cap mounting bolts. Tightening torque: 1st pass - 30 Nm; 2nd pass - turn 90° 2 - connecting rod cap....
Engine — removal and installation
Removal Attention! The engine is removed without the gearbox. 1. Remove the fairing grille. 2. Disconnect the ground (-) wire terminal from the negative...
Removal Attention! The engine is removed without the gearbox. 1. Remove the fairing grille. 2. Disconnect the ground (-) wire terminal from the negative...
Compression in cylinders — check
Compression testing allows you to draw conclusions about the engine's condition. Based on the results of the test, you can judge whether the engine has...
Compression testing allows you to draw conclusions about the engine's condition. Based on the results of the test, you can judge whether the engine has...
Oil pump and power steering pump bracket — design description
8.0. Oil pump and power steering pump bracket: 1 - auxiliary drive V-belt tensioner lever 2 - bolt. Tightening torque - 30 Nm 3 - plug for tension roller of...
8.0. Oil pump and power steering pump bracket: 1 - auxiliary drive V-belt tensioner lever 2 - bolt. Tightening torque - 30 Nm 3 - plug for tension roller of...
Oil pump and power steering pump bracket — removal and installation
Removal 1. Drain the coolant. 2. Remove the accessory drive V-belt (see the relevant chapter). 3. Remove the power steering pump pulley mounting bolts, holding...
Removal 1. Drain the coolant. 2. Remove the accessory drive V-belt (see the relevant chapter). 3. Remove the power steering pump pulley mounting bolts, holding...
Oil pump — removal and installation
Removal 1. Remove the upper engine cover by removing the plugs and unscrewing the nuts (see arrows in the illustration). 9.1 Remove the upper engine protective...
Removal 1. Remove the upper engine cover by removing the plugs and unscrewing the nuts (see arrows in the illustration). 9.1 Remove the upper engine protective...
Oil radiator — removal and installation
Removal 1. Drain the coolant. 2. Remove the front bumper (see the relevant chapter). 3. Set the upper front cross member to the service position (see points...
Removal 1. Drain the coolant. 2. Remove the front bumper (see the relevant chapter). 3. Set the upper front cross member to the service position (see points...
Oil pan — design description
11.0. Oil pan: 1 - oil pan mounting bolt. Tightening torque - 10 Nm 2 - lower part of the oil pan 3 - oil pump chain cover 4 - sealing gasket. Installed on...
11.0. Oil pan: 1 - oil pan mounting bolt. Tightening torque - 10 Nm 2 - lower part of the oil pan 3 - oil pump chain cover 4 - sealing gasket. Installed on...
Oil pan — removal and installation
Removal Bottom of the oil pan 1. Remove the cap from the coolant expansion tank. Caution! When the engine is hot, before removing the expansion tank filler...
Removal Bottom of the oil pan 1. Remove the cap from the coolant expansion tank. Caution! When the engine is hot, before removing the expansion tank filler...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections of other Audi car models:
Power unit: Diesel engine Audi 80 B3 (1986-1991)
Power unit: Diesel engine Audi 100 C3 (1982-1990)
Power unit: Diesel engines Audi A4 B5 (1994-2001)
Power unit: Diesel engine 2.5L Audi A8 D2 (1994-2002)
Power unit: Fuel system (diesel) Audi Q5 Type 8R (2008-2017)
Power unit: Diesel engine Audi 80 B3 (1986-1991)
Power unit: Diesel engine Audi 100 C3 (1982-1990)
Power unit: Diesel engines Audi A4 B5 (1994-2001)
Power unit: Diesel engine 2.5L Audi A8 D2 (1994-2002)
Power unit: Fuel system (diesel) Audi Q5 Type 8R (2008-2017)
Share information:
- General information
- User manual
- Maintenance
- Troubleshooting
- Power unit
- V6 petrol engines
- V8 petrol engines
- Diesel engines
- Cooling and heating system
- Injection system (gasoline)
- Fuel system (diesel)
- Supply system
- Exhaust system
- Ignition system
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Chassis
- Brake system
- Car suspension
- Steering
- Body
- Body elements
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Power devices
- Electrical circuits
- Schemes (petrol engine 2.7 l)
- Schemes (petrol engine 4.2 l)
- Schemes (diesel engine 2.5 l)
- General information
- User manual
- Maintenance
- Power unit
- Engine repair
- Cooling system
- Fuel system
- Engine management
- Fuel system (diesel)
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Chassis
- Front suspension
- Rear suspension
- Steering
- Wheels and tires
- Brake system
- Body
- Exterior
- Interior
- Electrical equipment
- Air conditioner
- Equipment and devices
- Electrical circuits
- General information
- User manual
- Maintenance (gasoline)
- Maintenance (Diesel)
- Gasoline engines
- 4 cylinder engines
- 5 cylinder engines
- 6 cylinder engines
- Diesel engines
- 4 cylinder engines
- 5 cylinder engines
- Engine repair
- Removal and reassembly
- Cooling system
- Single point injection system
- Multipoint injection system
- MPI/MPFI injection system
- Fuel system (diesel)
- Exhaust system
- Ignition system
- Transmission
- Clutch
- Manual transmission
- Automatic transmission
- Drive shafts
- Chassis
- Brake system
- Front suspension
- Rear suspension
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Power devices
- Lighting and appliances
- Electrical circuits