Table of contents: Electric window lift motor, window… ↓ Removal and installation the window… ↓ Removal and installation the inner… ↓ Removal and installation the window… ↓ Installation diagram of external and… ↓ Removal and installation the glass… ↓
Electric window lift motor, window lift
1. Door: remove the door trim.
2. Window lifter: door glass removed.
3. Door glass.
4. Nut: 9Nm.
5. Bolt: 3 pcs.; 3.5 Nm.
6. Electric window lift motor.
Removal and installation the window lift motor
1. Electrical connector: Disconnect the electrical connector from the used door.
2. Electric window lift motor: removal: remove the door trim, unscrew the bolts "6" and remove the electric motor. window lift motor; installation: installation in reverse order, taking into account the following: the "arrow" clamps of the threaded pins of the window regulator must be fixed in the inner panel of the door, put on the el. attach the window lift motor to the threaded pins and tighten the "6" bolts. The window lift motor can be removed and installed in any position of the motor or the door glass. With the window switches connected, turn on the ignition and raise the door windows as far as they will go. Continue holding the window switch for approx. 2 seconds to activate base reg. and lifting and lowering functions.
3. Threaded pins.
4. Window lifter.
5. Bolt: 3.5 Nm.
Removal and installation the inner door panel trim
1. Trim: remove the door trim, remove the wiring harness "4" from the bracket "5", disconnect the bushing "2" of the cable drive on the trim of the inner door panel, remove the trim, be sure to start from the top.
2. Nozzle.
3. Cable drive.
4. Electric cable: release from bracket "5".
5. Bracket.
Removal and installation the window regulator
1. Lower window regulator mount.
2. Bolt: To remove the glass, just loosen it.
3. Window regulator: removal: door trim removed, window regulator electric motor removed, door glass removed, door inner panel trim removed; unlock the threaded pins of the window lift motor and pass it through the inner panel, loosen the upper nuts, unscrew the lower nut and remove the window lift from the door by moving it upwards.
4. Nut: unscrew to remove the window regulator.
5. Door: remove the door trim.
Lower window regulator mount
Loosen the lower bolt "2" and remove the window regulator "1" from the mount "3" in the direction of the arrow. Remove the electric window motor. Remove the door glass. Remove the loudspeaker. Unlock the fastening clamps of the threaded pins "arrow" of the window regulator using an 11 mm socket head, to do this, place the head on the threaded pins. Unlock clamp "1" of traction cable "2" from the inside of the guide of traction cable "1".
Remove plug "1, 3, 6". Unscrew the upper nuts "2". Loosen the lower bolts "5" in the window lift cable guide. Remove window regulator "4" from the door by moving it upwards.
Installation
Installation in reverse order. The clamps of the threaded pins "arrow" of the window regulator must be fixed in the inner panel of the door. Install a loudspeaker. Install the door glass. Set email. window lift motor.
Installation diagram of external and internal glass pressure bars
1. Door.
2. External glass pressure plate.
3. Inner pressure plate in the door cavity: door trim removed, remove upwards from the door flange.
4. Latch: as shown in the picture, insert the glass pressure plate into the retainer.
Removal and installation the glass guide
1. Glass guide: door trim and window frame removed, outside rear mirror. view removed, B-pillar trim on the front door removed, door glass removed; starting from the top, remove the glass guide from the A-pillar and the B-pillar from the side of the door, remove the glass guide from the door in an upward direction, to facilitate installation, lubricate the guide with a soap solution, insert the glass guide into the guide channel, as shown in the figure, insert the guide protrusions from the side. glass in the upper part of the door.
2. Door.
3. Door glass.