Table of contents: Working conditions and tools ↓ Special tool ↓
Bolts and nuts must be used clean and lightly oiled. Always inspect the surface of nuts and bolts for serviceability and eliminate any defects. In doubtful cases, use new threaded bolts and nuts.
Once loosened, self-protecting nuts should always be renewed.
Under no circumstances should grease be removed from nuts and bolts.
All sealing washers, gaskets, retaining plates, cotter pins and O-rings (o-ring of circular cross-section) must be replaced during assembly. The seals are also replaced if they were removed from the shaft. It is necessary to ensure that during installation the working cover is directed in the direction from which oil or grease can flow.
Attention! All work on the vehicle, in particular with the brake system and steering, must be carried out carefully and prudently. The vehicle's safe movement must be ensured after any repair.
Working conditions and tools
Repair work must be carried out in a clean, well-lit place. The size of the repair area must be sufficient to disassemble and lay out parts. In a well-lit workshop, work is done without fatigue and haste, the car is disassembled and assembled in a neat environment. Unfortunately, not everyone has such an ideal workplace, so you have to improvise.
In addition, it is necessary to have a complete and high-quality set of tools. The indispensable requirement here is quality, since a cheap tool can be very expensive, because it jumps off and destroys expensive parts. A good tool is offered by the company HAZET.
Special tool
| № | Tool | HAZET-№ |
| 1 | Impact screwdriver | 2272 |
| 3 | Screwdriver for various screws | 793/3 |
| 4 | Pockert engine tester | BOSCH |
| 5 | Ignition Timing Stroboscope | BOSCH |
| 6 | Diode tester | - |
| 7 | Sensitive plate gauge 0.05-1.0 mm | 2147 |
| 8 | Spring loaded brake calipers | 797 |
| 9 | Impulse compression collet for sealing valve body | 791-2 |
| 10 | Pressed mandrel for mortise stops on carburetor | 4519-1 |
| 11 | Exhaust Pipe/Chain Cutter | 2182 |
| 12 | Battery electrolyte tester | 802-1 |
| 13 | Pneumatic adapter for replacing seals | 3428 |
| 14 | Hydraulic nut breaker | 846-22 |
| 15 | Oil filter wrench | 2172 |
| 16 | Angle disc for three-dimensional controlled tightening device for screws, such as cylindrical head screws | 6690 |
| 17 | Set of keys for Allen screws | 2100/7R |
| 18 | Brush for cleaning poles and terminals 802-4 | |
| 19 | Valve grinding device | 795 |
| 20 | Magnet-searcher | 1976 |
| 21 | Torque wrench 20-200 Nm | 6122-ICT |
| 22 | Flat scraper for removing sealant residues in the cylinder head and engine block | 824 |
| 23 | Brake caliper file | 1968-1 |
| 24 | Connecting mandrel diameter 15-19 mm | 2173/1 |
| 25 | Device for pressing out heads of transverse steering rods | 779 |
| 26 | Wire stripping pliers | 1862 |
| 27 | Brass mandrel (mandrel) | |
| 28 | Steel wire bristle brush for cleaning brake caliper | 1968 |
| 31 | Punch, cotter pin for safety pins | 748Lgb-4 |
| 32 | Pin punch for hollow pins | 748Lgb-6 |
| 33 | Compression pressure gauge | |
| 34 | 1/2" x 1/4" Square Matching Device | 958-2 |
| 36 | Device for unscrewing threaded studs | 845 |
| 37 | Open double-sided overhead key for | 612S-10x11 |
| 38 | Brake line union nuts | 612S-12x14 |
| 39 | Impulse coupler for wipers, etc. | 1966-5 |
| Top Spark Plug Wrench 20.8mm | 2505-2 | |
| Fig. Spark plug wrench 16 mm | 2505-2 | |
| (with 105 hp) suitable | 2506 | |
| switchable 3/8-inch ratchet | 8816 GK |