I 1. Screw; 2. Coolant pipe holder; 3. Evaporator body; 4. Coolant supply pipe coolant flow from the engine; 5. Coolant supply pipe for coolant return flow to the engine; 6. O-ring. Replace. Lightly lubricate with coolant before installation; 7. Retainer: These clamps are installed at the factory and hold the coolant tubes in the factory heat exchanger; 8. Heat exchanger of the heating system. This version is installed by the manufacturer; 9. Fastening the coolant pipes in the replacement heat exchanger. Included in the scope of delivery of the replacement heat exchanger; 10. Washer. Included in the scope of delivery of the replacement heat exchanger; 11. Screw. Included in the scope of delivery of the replacement heat exchanger. Tightening torque 2.5 Nm; 12. Replacement heat exchanger of the heating system. This version is supplied as a spare part. Cover the heat exchanger with foam insulation according to the version of the climate control system and the car; 13. Cellular element. Provided for cars with a gasoline engine and for cars with a diesel engine, where the autonomous heater (additional equipment) controlled as add. Cover the cellular element with foam insulation according to the climate control design, installation; 14. Heating element of additional heater "Z35". It is intended for cars with diesel engines (also for cars where the autonomous heater (additional equipment) controlled as add.). Cover the heating element of the additional heater "Z35" with foam insulation according to the design of the climate control system, installation; 15. Bracket; 16. Mounting plate with actuator electric motor of left temperature flap "V158"; 17. Defrost flap servomotor "V107"; 18. Left mounting plate with left footwell flap actuator motor "V108" and left center deflector actuator motor "V110". With cam discs, intermediate lever and connecting rods. Lightly lubricate cam disc guides, shaft bearings and journals on flap levers (e.g. with "G 000 150" solid lubricant paste); 19. Left heating element housing (with temperature dampers). The control of the temperature flaps and, accordingly, the left heating element housing is different for cars with climate control, the "Komfort" and "Basis" versions. With climate control, the "Komfort" version installation, the temperature flaps (front left and back) are driven by various electric motors. Different designs (with one or two bolt connections at the bottom). Lightly lubricate the cam disc guides, shaft bearings, gear elements and also the journals on the throttle levers (e.g. with solid lubricating paste "G 000 150"); 20. Dentate segment; 21. Mounting plate with rear temperature flap actuator motor "V137". Removing the mounting plate with the rear temperature flap actuator motor "V137", removing the electric motor from the mounting plate. Control of the left and right temperature flaps is different for the "Komfort" and "Basis" air conditioning systems. With the "Komfort" air conditioning system, the shaft of the left rear temperature flap is driven via a toothed segment from the rear temperature flap actuator motor "V137". The right rear temperature flap is also driven via a connecting rod that works with this toothed segment from the rear temperature flap actuator motor "V137". Lightly lubricate the shaft bearings, toothed segments and also the journals on the flap levers (e.g. with solid lubricating paste "G 000 150"); 22. Defrost flap connecting rod; 23. Intermediate lever to the defrost flap actuator motor "V107"; 24. Connecting rod of rear temperature flaps; 25. Air distributor housing, air conditioning unit, "Komfort" version. Do not disassemble into parts. Different versions on vehicles with air conditioning unit in "Komfort" and "Basis" versions. Lightly lubricate the cam disc guides, shaft bearings, toothed elements, and also the journals on the flap levers (e.g. with solid lubricating paste "G 000 150"). With air conditioning unit "Komfort" version, a separator is installed (for distribution to right and left/front and rear streams). Additionally, a deflector with covers for indirect ventilation is installed on the left and right, as well as for supplying air to the rear deflector of the central console on the left and right. Various flaps (for example, the front panel and footwell deflectors on the left and right) are driven by separate electric motors. The flaps of the central deflectors of the front panel and the air duct to the rear deflectors of the central console on the left and right are respectively connected to each other by connecting rods and are driven by the executive electric motor of the center, left deflector "V110" and the executive electric motor of the center, right deflector "V111". Since 08.2007, air conditioners with an air distributor housing with an optimal arrangement of air ducts (versions "1" and "2") have been gradually installed; 26. Temperature sensor for the air vent, in the left footwell "G261". Installed in the left air vent in the footwell; 27. Wiring harness climate control, "Komfort" version settings. Various versions. Mark the location of the plugs before pulling them out, (similar plugs for different actuators and temperature sensors, can be accidentally mixed up). Secure the wiring harness to the mounting points provided on the body using clamps or fasteners so that it does not come into contact with moving parts; 28. Temperature sensor at the air outlet in the footwell on the right "G262". Installed in the footwell deflector on the right; 29. Cable tie; 30. Right heating element housing (with temperature dampers). The control of the temperature flaps and, accordingly, the housing of the right heating element is different for cars with climate control, the "Komfort" and "Basis" versions. With climate control, the "Komfort" version installation, the temperature flaps (front right and rear right) are driven by various actuator electric motors. Different designs (with one or two bolt connections at the bottom). Lightly lubricate the cam disc guides, shaft bearings, gear elements and also the journals on the throttle levers (e.g. with solid lubricating paste "G 000 150"); 31. Right mounting plate with right footwell flap actuator motor "V109" and with right center deflector actuator motor "V111". With cam discs, intermediate lever and connecting rods. Lightly lubricate cam disc guides, shaft bearings and journals on flap levers (e.g. with solid lubricating paste "G 000 150"); 32. Mounting plate with actuator electric motor of right temperature flap "V159"
The original version of the article is posted on the website AUDIMANUAL