- Stage 1 - 4
- Stage 2 - 60
- Step 3 - Tighten another 180°
Camshaft bearing caps - 20
Camshaft sprocket - 80
Fastening of a forward support of the engine to the block of cylinders — 25
Engine mounts - 35
Mounting the gearbox to the engine - 55
Camshaft belt cover - 10
Tensioner nut - 45
Rear cover bolt - 30
Water pump pulley - 20
Crankshaft sprocket bolt (oiled thread):
- Hex head - 180
- Double Hex - 90+180°
Intermediate shaft sprocket - 80
Valve cover - 10
Engine front lifting lug - 25
Engine Support Bracket - 35
Main bearing caps - 65
Seal flange intermediate shaft - 25
Front seal housing - 20
Flywheel / drive disc - 100
Connecting rod bearing cap nut - 30+90°
Tensioner nut - 45
Oil pressure switch - 25
Oil pump mounting bolts - 20
Cover and suction tube of the oil pump - 10
Drain plug of the pallet - 30
Pallet bolts - 20
5-cylinder engines
Cylinder head bolts:
- Stage 1 - 40
- Stage 2 - 60
- Step 3 - Tighten another 180°
Gearbox to engine
- M8 - 20
- M10 - 45
- M12 - 65
Subframe - 70
Front support arm - 45
Engine mounts - 45
Camshaft belt covers - 10
Camshaft sprocket - 10-valve engine - 30
Camshaft sprocket - 20 valve engine - 65
Camshaft gear bolt (using tool 2079 - see text) — 350
Valve cover - 10
Oil intake pipe of the oil pump - 10
Pan drain plug - 10 valve engine - 40
Pan drain plug - 20 valve engine - 30
Flywheel cover - 25
Pallet (10 valve engine) — 20
Oil pump - 10
Main bearing caps - 65
Flywheel / drive disc - 100
Camshaft belt tensioner - 20
Connecting rod bearing cap nut - 30+90°
Oil spray nozzle of the connecting rod bearing cap - 10
Camshaft Bearing Caps - 10 Valve Engine - 20
Camshaft bearing caps - 20 valve engine - 15
Camshaft belt rear cover - 20
Crankshaft pulley - 20
Oil check valve (20 valve engine) — 6
Oil pressure switch apron - 50
Pallet (20 valve engine):
- M6 - 10
- M8 - 20
Radiator Mounts (4 cylinder engine) — 10
Radiator Mounts (5 cylinder engine) — 20
Thermostat cover - 10
Temperature sensor - 10
Mounting the water pump to its body (4 cylinder engine) — 10
Fastening the water pump housing to the cylinder block (4 cylinder engine) — 20
Water pump pulley (4 cylinder engine) — 20
Electric fan shield - 10
Electric fan - 10
Fastening of the water pump to the block of cylinders (5 cylinder engine) — 20
fixing nut (ABS system) — 7
Wire fixing bolt "masses" (ABS system) — 20
Nut of fastening of a wire of weight" (ABS system) — 10
Wheel sensor mounting bolt (ABS system) — 10
Front brake caliper (girling system):
- Guide pin bolt - 35
- Frame bolt - 125
Front brake caliper (Teves systems):
- Guide pin bolt - 25
- Frame bolt - 125
Rear wheel brake cylinder - 10
Rear brake caliper (girling system):
- Guide pin bolt - 35
- Frame bolt - 65
Rear brake caliper (Teves systems):
- Guide pin bolt - 25
- Frame bolt - 65
Vacuum servo booster:
- Fixing nut - 25
- Bracket nut - 10
Bolt of the fitting of the pneumatic accumulator of the hydraulic servo amplifier - 35
Brake Master Cylinder Bolt - 25
Fastening the shift lever to the base plate - 25
Nut of a fork of the lever of a gear change - 10
Gear lever base plate - 10
Clamping bolt of draft of inclusion of transfers — 25
Coupling bolt of draft of inclusion of transfers — 20
Mounting the rear cushion to the gearbox - 40
Fastening the rear cushion to the beam - 100
Mounting the gearbox to the engine:
- M8 - 25
- M10 - 45
- M12 - 65
Multifunction sensor - 25
5th gear/reverse gear retainer - 10
Multifunction sensor connector - 10
Main gear cover - 25
The guide sleeve of the clutch release mechanism - 35
Relay Shaft Torx Bolt - 40
Reverse gear axle - 35
Retainer Torx Bolt - 25
Mounting the rear crankcase to the main crankcase - 25
Nut of the lever of a choice of transfers — 8
Gear selector cable support - 15
Fastening the torque converter to the drive disk - 30
Mounting the gearbox to the engine - 55
Mounting the oil pump of the radiator to the gearbox - 40
Cover of a case of the main transfer — 25
Oil pan - 20
Strainer cover - 3
Clamp bolt distributor - 11
Fastening the inner CV joint to the flange:
- Bolt M8 - 45
- Bolt M10 - 80
Drive shaft outer nut (hub nut) — 265
Drive shaft outer bolt (hub bolt):
- Bolt M14 — 120+90°
- Bolt М16 — 200+90°
Wheel bolts - 110
Exhaust pipe gear mount - 30
Mechanical fuel pump mounting bolts - 20
Fuel tank - 25
Exhaust manifold - 25
Exhaust coupling - 40
Warm-up valve - 10
Cold start valve - 10
Fuel filter fitting - 20
Pipe fitting for measuring the content of CO - 30
Fastening of a final exhaust pipe to a collector — 35
Fastening the sensor of the Lambda system to the catalytic converter - 50
Carburetor flange - 13
Intake manifold - 25
An arm of fastening of an inlet collector to final — 20
Intake air pre-heater - 10
Carburetor cover - 5
Heating regulator fitting - 20
Start fuel switch 30
Throttle body - 20
Diaphragm pressure regulator fitting - 20
Visitor comments