Table of contents: Seat Rail Cover ↓ Removal ↓ Installation ↓ Backrest of the rear seat ↓ Seat back release parts and… ↓ Cover for the device for… ↓
1. Multi-seat; 2. Rear seat belt buckle; 3. Cover for the device for transporting long loads; 4. Right rear seat 1/3; 5. Seat back release mechanism; 6. Rear center armrest; 7. Headrest; 8. Rear seat 2/3 left; 9. Overlay; 10. ISOFIX child seat anchorages. Welded to the seat frame, to replace the child seat anchorage remove the seat frame and replace;The instructions apply to the rear left seat 2/3, for the right rear seat 1/3 they are similar.
1. Fastening attachments. 2 pcs. for fastening the rear seat. Clipped into the seat frame. After each removal of the rear seat cushion, the fastening attachments must be replaced; 2. Multi-seat; 3. Seat guide cover. Remove from the dismantled seat; 4. Bolt. 4 pcs. 50 Nm; 5. Back seat; 6. Child seat mounting pad (ISOFIX). 2 pcs. Fastened to the child seat mounting clamps (ISOFIX) welded to the seat frameSeat Rail Cover
Remove the seat rail cover "arrow".
Removal
The description of removal and installation on the left rear seat 2/3 is given. The same for the right rear seat 1/3. Remove the ISOFIX child seat mounting pads. Take hold of the rear seat from below with both hands on one side. Pull the rear seat "1" upwards with both hands "arrow A" so that the hook "2" of the rear seat pops out of the fastening nozzle "3". Repeat these operations on the opposite side "arrow B".
Option complete with seat heating system: Disconnect the plug connector of the seat heating system. Remove the seat from the car.
Installation
Remove the used fastening attachments "5" from the seat frame. Check the seat frame in the area of the attachments for deformation, align if necessary. Press the new attachments into the seat frame until they click. Installation in reverse order: install the rear seat, to do this, push the rear wire hooks "3" under the seat frame 2 - "arrow". Press the front wire hooks "4" into the fastening attachments "5" on the seat frame until they are audibly locked. Remember that the plug connectors must be inserted until they stop and click.
Backrest of the rear seat
The instructions apply to the backrest of the rear left seat 2/3, for the backrest of the right rear seat 1/3 they are similar.
1. Upper flexible seat back release cable; 2. Seat frame; 3. Lower flexible seat back release cable; 4/11. Bolt. 2 pcs. 36 Nm; 5. Bolt; 6. Rear seat belt buckle in the middle; 7. Shaft; 8. Backrest of the rear seat; 9. Rear seat belt fittings in the middle; 10. Bolt; 12. Bolt. 36 Nm; 13. Rear seat backrest cover; 14. Bolt. 3.8 NmSeat back release parts and components
The instructions apply to the adjustment mechanism for the rear left seat back 2/3, the adjustment mechanism for the rear right seat back 1/3 is similar.
1. Connecting module for upper and lower flexible cable. Fixed to the seat frame; 2. Back seat; 3. Upper cable bracket. 4 pcs.; 4. Upper flexible seat back release cable; 5. Bolt 1.5 Nm; 6. Seat back release lever; 7. Lever bracket; 8. Nut. 2 pcs. 3 N·m 9. Release lever; 10. Washer; 11. Bolt. 18 Nm. Use thread sealant; 12. Lower flexible seat back release cable; 13. Backrest adjustment mechanism handle;Cover for the device for transporting long loads
1. Back seat. 2/3 left; 2. Lock washer; 3. Bolt. Self-locking. 18 Nm. Replace after each removal, the threaded hole for the bolt should be cleaned, for example with a tap; 4. Armrest; 5. Cover for the device for transporting long loads; 6. Unlocking the cover of the device for transporting long loads; 7. Bolt. 4 pcs. 3.8 Nm; 8. Cover plate for the lock; 9. Lock of the cover of the device for transporting long loads; 10. Bolt. 2 pcs. 22 Nm(Read the original source on the website: audimanual.ru)